Kärcher G 2600 FCE Page 14 Operator'S Manual Download

Page: 14 / 14

English

If the symptom you are experiencing is not listed

above, or if the provided solutions do not solve your

issue, please visit our extensive online trouble-

shooting database at:

www.karcher-help.com

Symptom

Cause

Solution

NO DETERGENT

Detergent suction tube not

properly

connected to the machine

Check connection

Detergent is too thick

Dilute detergent, for best results use Kärcher
detergent

Filter on detergent suction

tube is clogged

Run warm water through ﬁ lter to remove
debris

Damaged or clogged deter-

gent suction tube

Remove obstruction or replace detergent
suction tube

A high pressure nozzle is

attached

Replace with black detergent nozzle

Spray nozzle is obstructed

Blow out or remove debris with ﬁ ne needle

GARDEN HOSE

CONNECTION

LEAKS

Loose ﬁ ttings

Tighten ﬁ ttings

Missing/worn rubber

washer

Insert new washer

SPRAY WAND

LEAKS

Spray wand not properly

attached

Turn the swivel nut of the gun clockwise until
connection is tight

Broken o-ring or plastic

insert

Visit www.karcher-help.com or locate a ser-
vice center at www.karcher-service.com

PUMP IS NOISY

Not enough gas or engine

oil

Check that hoses and ﬁ ttings are air tight.
Turn off machine and purge pump by
squeezing trigger gun until a steady ﬂ ow of
water emerges through the nozzle

WATER LEAKS

FROM PUMP (UP

TO 10 DROP PER

MINUTE IS PER-

MISSIBLE)

Loose ﬁ ttings

Check quick connect ﬁ ttings

Water seals are damaged
or worn.

Visit www.karcher-help.com or locate a ser-
vice center at www.karcher-service.com

Thermal protection device

is activated.

Thermal protection device will auto reset.
Do not run pump for more than 5 minutes
without spraying

OIL DRIP

Oil seals are damaged or

worn

Visit www.karcher-help.com or locate a ser-

vice center at www.karcher-service.com

Summary of Contents for G 2600 FCE















Search results

Summary of Contents for G 2600 FCE

Reviews:

Related manuals for G 2600 FCE

Brands by name

Popular brands

Kärcher G 2600 FCE, Operator'S Manual

Search results

Summary of Contents for G 2600 FCE

Reviews:

Related manuals for G 2600 FCE

Brands by name

Popular brands