background image

9.801-811.0 • Rev. 06/17

    

PRESSURE WASHER   

SERVICE MANUAL

24

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSE

SOLUTION

PUMP RUNNING 

NORMALLY BUT  

PRESSURE LOW ON  

INSTALLATION 

Pump sucking air

Check water supply and possibility of air seepage.

Check valves sticking

Check and clean or replace if necessary.

Unloader valve seat faulty

Check and replace if necessary.

Nozzle incorrectly sized

Check and replace if necessary.

Worn piston packing

Check and replace if necessary.

FLUCTUATING  

PRESSURE

Valves worn

Check and replace if necessary.

Blockage in valve

Check and replace if necessary.

Pump sucking air

Check water supply connections.

Worn piston packing

Check and replace if necessary.

Insufficient water

Check filter and hose for breakage.

PRESSURE LOW AFTER 

PERIOD OF NORMAL 

USE

Nozzle worn

Check and replace if necessary.

Suction or delivery valves worn

Check and replace if necessary.

Suction or delivery lines blocked

Check and clean if necessary.

Unloader valve seat worn

Check and replace if  necessary.

Worn piston packing

Check and replace if necessary.

Water temperature excessive

Reduce to below 160

F.

PUMP NOISY

Air in suction line

Check water supply and connections on suction 
line.

Broken or weak suction or delivery 
valve spring

Check and replace if necessary.

Foreign matter in valves

Check and clean if necessary.

Worn bearings

Check and replace if necessary.

Excessive temperature of water

Reduce to below 160

F.

PRESENCE OF WATER 

IN PUMP OIL

Oil seal worn

Check and replace if necessary.

High humidity in air

Check and replace if necessary.

Piston packing worn

Check and replace if necessary.

WATER DRIPPING FROM 

UNDER PUMP

Piston packing worn

Check and replace if necessary.

O-ring plunger retainer worn

Check and replace if necessary.

WATER DRIPPING FROM 

PUMP PROTECTOR

Water supply pressure too high (over 
90 PSI)

Lower water supply pressure using a regulator.

Spray gun is in the off position for over 
5 minutes

Turn machine off if not in use for over 1-2 minutes.

OIL DRIPPING

Oil seal worn

Check and replace if necessary.

EXCESSIVE VIBRATION 

IN HIGH PRESSURE 

HOSE

Irregular functioning of the pump 
valves

Check and replace if necessary.

MOTOR DOES 

NOT START WHEN 

SWITCHED ON

Plug not well connected or lack of 
power supply

Check plug, cable and switch.

WHEN SWITCHING ON 

THE MACHINE, MOTOR 

HUMS BUT DOES NOT 

RUN

Main voltage is insufficient, lower than 
the minimum required

Check to make sure main power supply is ad

-

equate.

The pump is stuck or frozen

Check by turning the motor manually.

MOTOR STOPS

Tripped thermal overload due to over

-

heating

Check that main voltage corresponds to the speci

-

fications. Wait a few minutes before turning on the 
machine again by resetting the GFCI cord.

Summary of Contents for 1.106-124.0



























Reviews: