KARCEPTS KIM01 Installation Instructions Manual Download Page 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Installation Instructions for Part #: KIM01 

K20A/A2/A3/Z1 Throttle Body To RBC/RRB/RBB 

Intake Manifold Adapter 

 

This adapter provides the SOLUTION for directly bolting up a  

02-06 RSX-S/ITR or 02-05 Civic Si/CTR Throttle Body to an  

Accord Euro R, 06-08 Civic Si, or 04-05 TSX Intake Manifold.   

 

Ease of fitment has been confirmed for the following vehicle/engine/mount combinations: 

-1992-1995 Honda Civics equipped with a K20 engine and Hasport EGK1 engine mounts 
-1996-2000 Honda Civics equipped with a K20/24 engine and Hasport EKK2 engine mounts 
-1994-2001 Acura Integras equipped with a K20 engine and Hasport EGK1 engine mounts 
-2002-2006 Acura RSX-S/Honda ITRs with a K20 engine and all available engine mounts 

 

 

          Note: If attempting to install a throttle body and intake manifold into a vehicle/engine/mount     
          combination not currently confirmed, modifications to your chassis may be extensive. 

 

 

 

   

 

 

 

     

 

Karcepts, Inc. 

www.karcepts.com 

[email protected] 

Summary of Contents for KIM01














Reviews: