background image

 

 2 

    

 Note 

 

After adjusting, drop down upper cutter at the bottom 

position ( bottom dead point ) in pulling lever F 

direction to H.  Then, confirm whether upper cutter 

and lower cutter shall meet each other at 1 mm 

distance or not. 

 Note 

 

When checking the proper overlapping between upper 

cutter and lower cutter, move upper cutter by your 

hand. 

2

ADJUSTMENT

ELECTRIC TYPE

   

2222----1 Height of Cutter

1 Height of Cutter

1 Height of Cutter

1 Height of Cutter    

Loosen screw E and adjust lever F in order to set 
24 mm of the distance between lower cutter and 
upper cutter at the top position (top dead point). 
During this adjustment, do not forget to align 
between surface G (surface of lever F) and edge 
surface of solenoid shaft. 

 
 
 
 
 
 
 

2222----2 Overlapping of Cutter

2 Overlapping of Cutter

2 Overlapping of Cutter

2 Overlapping of Cutter    

1.  Loosen screw I, then loosen screw J until 

disappearing of pressurized power of upper 
cutter. 

2.  Loosen screw K, then adjust screw L in order 

to overlap properly between upper cutter and 
lower cutter. 

 
 
 
 
 

2222----3333 Power of Upper Cutter

 Power of Upper Cutter

 Power of Upper Cutter

 Power of Upper Cutter    

After loosen screw I, then adjust the pressurized 
power of upper cutter against lower cutter by screw 
J. 

 
 
 
 
 
 
 
 
 

 

 

 

 

Summary of Contents for MC 30








Reviews: