background image

  

iii 

  

 

 

 

Important Safety Information 

In this manual, warning types and classifications are defined as follows: 
 

[Classification] 
 

       

WARNING: To Prevent Serious Injury or Death 

Indicates a potentially hazardous situation which, if not avoided, may result in 
serious injury or death. 

       

CAUTION: To Prevent Damage to the Product 

Indicates a potentially hazardous situation which, if not avoided, may result in 
damage to the product that may void the product warranty.  

 

[Description of Symbols] 

 

Indicates a condition (including danger) that requires caution.  The subject of each caution 
is illustrated inside the triangle (e.g., the symbol shown to the left is the high temperature 
caution).  
 

 

Indicates a prohibition.  Do not take the prohibited action shown inside or 
near this symbol (e.g., The symbol shown to the left prohibits disassembly). 
 

 

 

Indicates a mandatory action.  A specific action is described near the symbol. 
 

WARNING 

 

 
 

 

Do not disassemble, modify or repair the instrument. 

 

…… 

Misuse of the instrument may result in electric shock, fire, or 

 damage to the instrument, etc. 
 

…… 

 A 3B laser diode is used as the optical source inside the 

instrument. Therefore, never attempt to disassemble the 
instrument as it is extremely dangerous. 

 

Do not 

modify/disassemble 

 

Summary of Contents for 3720-06
























Reviews: