KanexPro MP-SC-6E User Manual Download Page 15

Page: 15 / 20

Compact Scaler Switcher 6x1

①

Standby button

Enter/ exit standby mode.

②

Input channel selection buttons

Selection video source via pressing
corresponding button (audio switched following
the corresponding VGA).

③

Auto button

Enter/ exit auto-switching mode.

④

Resolution selection buttons

Select resolution via pressing corresponding
button.

⑤

Output black button

Press to switch on/off Audio& Video output

4.4 Firmware Updating

MP-SC-6E supports firmware updating via USB flash disk. The procedures as follows:

Step1.

Copy the file “

MERGE.bin

” to the root directory of a USB flash disk. (Make sure

the

file is copied to the root directory for normal use. The “MERGE.bin” file is

provided/ authorized.

Step2.

Plug the USB flash disk to MP-SC-6E

FIRMWARE

port on its rear panel.

Step3.

Press the button “

RESOLUTION/FW UPDATE

” for

7 seconds or more

update the firmware automatically. Or send command

50698%

to update

software.

5. Specification

Video Input

Video Output

Input

4 HDMI, 2 VGA

Output

1 HDMI

Input
Connector

4 female HDMI (Type-A)
2 female VGA (15Pin)

Output
connector

1 female HDMI

Summary of Contents for MP-SC-6E




















Search results

Summary of Contents for MP-SC-6E

Reviews:

Brands by name

Popular brands

KanexPro MP-SC-6E, User Manual

Search results

Summary of Contents for MP-SC-6E

Reviews:

Brands by name

Popular brands