background image

 

10

 

 

IN THE EVENT OF A PUNCTURE 

If you suspect a puncture follow the following: 

1. 

Undo the inflation/deflation valve from the pole and re-attach ensuring that 
the tube does not twist and that the valve is firmly connected. 

2. 

Re-inflate the AirPole. 

3. 

If tightening the valve does not solve the problem then the AirPole may be 
punctured.   

 

TO REMOVE AN AIRPOLE 

 
3. 

Unzip the sleeve holding the AirPole. 

4. 

You should now be able to remove the AirPole. 

5. 

Unzip the protective cover of the AirPole, whilst deflated, to expose the 
inflatable tube.  

6. 

Locate the puncture.  This is made easier if you blow some air into the tube.    
For small holes it may be necessary to submerge the inflatable tube in 
water. 

7. 

Once located the tube can be repaired using repair tape.  We recommend 
Kampa Tent & Awning Repair Tape - available from your dealer. 

 
The repair can be enhanced by using a combination of the tape with Kampa 
Repair Solution. 
 
Follow the manufacturers instructions to repair.  
 
 
Another alternative is to replace the tube.  Spares are available from your dealer 
or direct from Kampa. 
 
Once a repair or replacement has been made, the AirPole can simply be zipped 
back into the sleeve. 

Summary of Contents for Travel Pod Maxi AIR













Reviews: