background image

12

Care and Maintenance

•  Ensure that the main power 

‘ON/OFF’ switch of the heater 

is switched OFF and the unit is 

disconnected from the power 

outlet before cleaning.

•  Use a clean, dry cloth to clean 

the external surfaces of the 

heater. If the heater has collected 

dust or dirt inside the unit or 

around the elements, have the 

unit cleaned by a qualified 

service agent. Do not operate  

the heater in this condition. 

•  Do not attempt to open the  

case of the heater at any 

time as there are no customer 

serviceable parts inside. When 

not in use, store the heater 

(preferably in its original box) in  

a cool, clean and dry location.

Cleaning the Filter 

•  Your Kambrook Ceramic Tower 

Heater comes with a mesh filter 

located at the rear of the heater 

to help keep dust and debris 

away from the working parts. It is 

recommended to regularly check 

your heaters filter for clogging 

and dust build up. The filter 

should be checked after every 

use to ensure efficient heating 

performance.

•  Always switch the main ‘ON/OFF’ 

switch of the heater to OFF, then 

disconnect from the power outlet 

prior to removing the filter for 

cleaning.

•  To access the filter, ensure the 

heater is in the upright position 

and then remove the filter cover 

by pulling down on the two 

release levers at the top of the 

cover and then carefully pull out 

the cover until it is completely free 

from the heater. 

•  It is then necessary to separate the 

mesh from the filter cover. Once 

separated, shake both the filter 

cover and the mesh filter into a 

rubbish receptacle until all fine dust 

particles and debris are removed. 

Wipe over with a soft, dry cloth if 

required to remove particles.

•  To replace, reinsert the mesh filter 

to the filter cover, align the two 

tabs at the back of the filter cover 

with the two holes at the back of 

the heater and then press down 

on the cover until it “clicks”.

Hints & Tips to Retain Heat  

in Your Home 

•  Don’t overheat your home. The 

temperature of a heated room  

in winter should be 18–21°C.

•  Your heater will work more 

efficiently if you stick to 

Kambrook’s recommended 

clearance spaces.

•  Choose the right size heater for 

the room type you want to heat.

•  Zone off unoccupied rooms by 

closing doors and only heat the 

main living areas. Fit window 

coverings like curtains to halve 

winter heat loss.

•  Put draft stoppers, such as a  

rolled up towel, at the bottom  

of outside doorways to keep  

out cold air.

•  Keep the heat in and the cold  

out by installing wall and  

ceiling insulation.

•  Avoid placing items too close to 

the heater (both at the front and 

back) for optimal air flow.

Summary of Contents for KCE340GRY

















Reviews: