background image

10

NOTE: 

When the unit is plugged 

into an electrical outlet and 

the outlet is turned on, the 

room temperature display will  

illuminate on the LED screen 

even though the tower fan is not 

operating. This is Standby mode.

NOTE: 

The tower fan is fitted with 

a power saving feature. When 

any of the 3 mode types are 

selected or the timer function 

is set, the LED display panel will 

automatically switch off after 

30 seconds, only displaying 

the temperature dimly on the 

screen. Press any key to turn the 

display on again. 

To turn the tower fan on, press the  

‘POWER’ button once; the unit will  

be in NORMAL fan mode at LOW  

speed setting. 

Setting the Fan Speed

The tower fan has three fan speed 

settings; LOW  , MEDIUM 

 and  

HIGH 

.

Pressing the ‘SPEED’ button once  

will set the tower fan into LOW   

speed setting.
Pressing the ‘SPEED’ button  

twice will set the tower fan into  

Medium 

 speed setting. 

Pressing the ‘SPEED’ button three times 

will set the tower fan into  

HIGH 

 speed setting.

NOTE: 

The SPEED indicator bar 

on the control panel will flash 

continuously during these cycles. 

To turn the tower fan OFF, press the 

‘POWER’ button and turn off at the 

power outlet and remove the plug from 

the power outlet.

Setting the Nature and 

Reduction Mode 

Your tower fan has a NATURE 

  

and REDUCTION 

 setting.

Both the NATURE 

 and  

REDUCTION 

 modes can be  

used on any fan speed. The LED  

screen will indicate what mode  

the fan has been set in.

Nature Mode

The NATURE 

 

mode simulates the 

natural rise and fall of the wind  

over time, with speed settings 

automatically cycling between low, 

medium and high.
At any fan speed setting, pressing the 

MODE button once will turn the tower 

fan into NATURE 

 mode.

To turn the NATURE 

 mode OFF, press 

the MODE button twice, the fan will now 

be in NORMAL operation mode.

Reduction mode

The REDUCTION 

 mode allows you to 

pre-select a variation in speed which 

automatically decreases the fan speed 

over time.
The REDUCTION 

 mode only applies in 

the MED or HIGH speed settings.
Once the MED or HIGH fan speed is 

selected, press the MODE button twice 

will turn the tower fan into REDUCTION 

 

mode. 

After 30 minutes, the selected setting will 

drop to the next lowest setting.  

For example if the fan speed is set  

at MEDIUM, after 30 minutes it will drop 

Using Your Kambrook Tower Fan 

continued

Summary of Contents for Arctic KFA837
















Reviews: