Kamasa-TOOLS K 10252 Operating Instructions Manual Download Page 4

Kamasa Tools is a trade mark of KG Knutsson AB, SE 191 81 Sollentuna, Sweden, Phone +46 8 92 30 00  www.kamasatools.com

additional safety rules for charger & battery pack

warning!

1.  Do not charge battery pack when temperature is below 10°C (50°F) or above 40°C (104°F).

2.  Do not attempt to use a set-up transformer, an engine generator or DC power receptacle.

3.  Do not allow anything to cover or clog the charger vents.

4.  Always cover the battery pack terminals with the battery pack cover when the battery pack: is  

not used.

5.  Do not short the battery pack.

6.  Do not touch the terminals with any conductive material.

7.  Avoid storing battery pack in a container with other metal objects such as nails, coins, etc.

8.  Do not expose battery pack to water or rain, A battery pack short can use large current flow,  

overheating, possible burns and even a breakdown.

9.  Do not store the machine and battery pack in locations where the temperature may reach or  

exceed 50°C (122°F)

10.  Do not incinerate the battery pack even if it is severely damaged or completely worn out.  

The battery pack can explode in a fire.

11.  Be careful not drop, shake or strike battery pack.

12.  Do not charge inside a box or container of any kind. The battery pack must be placed in a well  

ventilated area during charging.

For extension of the battery lifetime, the lithium-ion battery is designed with protection functions to 

stop the output. In the case of described below, when using this product, even if you are pulling the 
switch, the motor may stop. This is not malfunction but the result of protection function. 

  When the battery power remaining runs out, the motor stops. 

  If the tool is overloaded, the motor may stop. In this case, release the switch of tool and eliminate  

  causes of overloading. After that you can use it again. 

  If the battery is overheated under overload work, the battery power may stop. In this case stop  

  using the battery and let the battery cool. After that you can use it again.

13.  Do not leave batteries unused for extended period of time. Recharge the battery every 3–6 months 

and bring Li-Ion battery to 40–80% of charge level before storage.

14.  Li-Ion batteries are sensitive to high temperature and should be kept in a cool, dry and out of direct 

light exposure. Ideal temperature for operation and storage is below 25°C (77°F).

Summary of Contents for K 10252













Reviews: