A)
B)
C)
D)
E)
F)
G)
H)
A)
B)
C)
D)
E)
F)
G)
Remove cardboard and plastic cover
from pedal board.
Insert the beater (SC-LBDB) into the
beater holder (GP-6064) and adjust it to
your desired height.
Insert the pedal spring (SC-0052) onto
the spring cam (GP-6080) using the clip
attached to the spring.
To adjust the spring tension to your
desired response, loosen both upper
and lower finger nuts to increase or
decrease the tension, then re-tighten the
finger nuts.
Slide the pedal frame onto the bass
drum hoop then tighten the hoop clamp
(GP-6065) onto to the bass drum hoop.
To avoid pedal slippage and bass drum
movement, we recommend placing the
bass drum and pedal onto a carpeted
surface.
Lubricate metal-to-metal contact points
periodically to insure smooth operation.
We suggest #SC-GLO Gibraltar Pedal
Lubricant.
Gibraltar 6600 Series Hardware
Replacement Part Numbers
1 - SC-LBDB Light Weight BD Beater
2 - GP-6079 Double Chain Cam
3 - GP-6064 Beater Holder
4 - SC-0121 Key Screw 8mm
5 - SC-0129 Key Screw 6mm
6 - SC-0129 Fastening Screw 6mm
7 - GP-6080 Spring Cam Assembly
8 - GP-0052 Pedal Spring
9 - GP-5103 Spring Tension Assembly
10 - GP-4007 Double Chain Assembly
11 - GP-6033 Pedal Board Complete
12 - GP-0020 Anchor Spur Assembly
13 - GP-6065 Black Hoop Clamp
14 - GP-6066 Hoop Clamp Key Screw 8mm
15 - GP-6067 Fixed Rock Plate
16 - SC-0128 Fastening Screw 5mm
17 - SC-0129 Fastening Screw 6mm
18 - GP-3030R Connecting Rod w/ U-Joint
19 - GP-3030L Connecting Rod w/ U-Joint
20 - GP-3029 Center Connecting Shaft
Check out the entire line of
Gibraltar Hardware products at …
www.GibraltarHardware.com
1
3
2
5
4
6
7
8
9
11
13
12
14
10
1
3
14
2
10
2
4
6
7
8
9
11
11
12
15
16
17
18
19
16
Setup Instructions
6611 Series Single Pedal
Setup Instructions
6611DB Series Double Pedal
Remove cardboard and plastic cover
from pedal boards.
Insert the beaters (SC-LBDB) into the
beater holders (GP-6064) and adjust
it to your desired height.
Insert the connecting rod assembly
into the right and left axles on each
end of the pedal frames. Connect
both rods with the center connecting
shaft (GP-3029). Adjust the extension
rods to the desired length.
Insert the pedal spring (SC-0052)
onto the spring cam pivot hole
(GP-6080) using the clip attached to
the spring.
To adjust the spring tension to your
desired response, loosen both upper
and lower finger nuts to increase or
decrease the tension, then re-tighten
the finger nuts.
Slide the pedal frame onto the bass
drum hoop then tighten the hoop
clamp (GP-6065) onto the bass drum
hoop.
To avoid pedal slippage and bass
drum movement, we recommend
placing the bass drum and pedal onto
a carpeted surface.
Lubricate metal-to-metal contact
points periodically to insure smooth
operation. We suggest #SC-GLO
Gibraltar Pedal Lubricant.
15
15
20
