Replacement Part Numbers
1 - GP-0016 Upper Pull Rod
2 - SC-4421D Hi-Hat Clutch
3 - SC-HHCF Cup Felt
4 - SC-HHFW Flat Washer
5 - GP-6069 Upper Height Adjust Tube
6a - GP-2005 3/4" Nylon Inner Sleeve
6b - GP-2002 1" Nylon Inner Sleeve
7 - GP-2080 1" Fitted Memory Lock
8 - GP-6030 Wing/Short Bolt Set 6mm
9 - GP-6070 Hi-Hat Stand Base
10 - SC-0009 Wing Bolt 8mm
11 - GP-6032 Hi-Hat Chain
12 - GP-6033 Pinned Footboard
13 - GP-0021 Radius Rod for HiHat
14 - SC-PC09 Rubber Foot
15 - GP-0020 Anchor Spur Assembly
16 - GP-6071 Snare Basket
17 - GP-6052 Wing Nut/Bolt Assembly 8mm
18 - GP-6072 Upper Height Adjust Tube
19 - GP-6073 Lower Base Assembly
20 - SC-13P2 Wing Nut 8mm
21 - SC-CFS/4 Small Cymbal felt
22 - SC-19B Cymbal Sleeve 8mm
23 - GP-6062 Cymbal Tilter Assembly
24 - GP-6055 Wing Nut / Bolt Assembly 8mm
25 - GP-6056 Knurled Boom Arm
26 - GP-6068 Hex Bolt/ Wing Nut Assembly
27 - GP-6074 3/4" Upper Height Adjust Tube
28 - GP-6075 1" Middle Tube
29 - GP-6076 Lower Base Assembly
30 - GP-6077 3/4" Upper Height Adjust Tube
31 - GP-6078 3/4" Fitted Memory Lock
Check out the entire line of
Gibraltar Hardware products at …
www.GibraltarHardware.com
Gibraltar 6600 Series Hardware
1
2
3
4
5
7
6b
8
10
11
12
13
9
14
20
21
24
10
14
14
8
15
10
18
16
17
19
26
22
24
25
8
14
30
22
29
28
20
27
10
6b
8
21
8
6b
29
23
23
A)
B)
C)
D)
E)
F)
G)
Setup Instructions
6607 Series Hi-Hat Stand
Remove cardboard and plastic cover from pedal board and
attach the Radius Rod (GP-0021) to the frame.
Unfold and adjust the tripod legs to be flush to the ground and
slightly raise the middle frame.
Screw the Upper Pull Rod (GP-0016) into the lower base pull
rod stem.
Place the Upper Height Adjust Tube (GP-6069) into the base
and adjust to the desired position. Use the Fitted Memory Lock
(GP-2080) on the tube to retain this position.
Place the bottom hihat cymbal onto the hihat stand Cup Felt
(SC-HHCF) facing upwards.
Place the top hihat cymbal into the Hi-Hat Clutch (GP-4421D),
inserting it between the two small felts on the clutch, then slip it
onto the upper pull rod.
Secure the upper hihat cymbal with clutch onto the pull rod
leaving approximately 1" spacing between the upper and lower
hihat cymbals, then adjust to the desired spacing.
A)
B)
C)
D)
Setup Instructions
6606 Series Snare Stand
Open the tripod base of the
snare stand (GP-6073) and
place it in an upright position.
Insert the upper snare tube
(GP-6072) into the stand
base.
Open the snare basket
(GP-6071) to fit the snare
drum to be used.
Once the snare drum is
placed in the basket, tighten
the basket to secure the drum.
Be aware that over tightening
the basket may choke the
drum sound, limiting the
response.
A)
B)
C)
D)
Setup Instructions
6609, 6610 Series
Cymbal Stands
Open the tripod stand base
of the cymbal stand and
place it in an upright position.
Insert the middle and, or,
upper cymbal tube into the
stand base.
Insert the boom arm, 6609
only, into the upper tilter
assembly.
Use the tilter on the upper
height adjust tube and, or,
the boom arm to position
your cymbal to the desired
angle.
7
6b
7
8
31
31
7
6a
6a
28
