INTRODUCTION
Thank you for purchasing the KAM TRI 160
LASER”. To optimize the performance of this
product, prior to use, please read these
operating instructions carefully to familiarize
yourself with the basic operations of this unit.
The TRI 160 LASER has the KAM funky design
and is an amazing Laser effect. Please keep
these user instructions in safe place for future
reference. This unit has been Tested at the
factory before being shipped to you.
There is no Assembly required.
Warning!
To prevent or reduce the risk of electrical shock
or fire, do not expose this unit to high
Temperature / rain or moisture.
Laser Class 3B product. National
Regulations must be adhered to at all steps of
installation.
(In Germany apply DIN 56912 and BGVR LASER
note: additional Regulations may apply).
Unintended reflections of the laser beam from
reflective or metallic surfaces can be
dangerous.
This appliance is to used by Qualified personnel
only.
Laser Radiation Warning
This unit uses diode lasers in green and red. This
is CLASS 3B laser product.
Avoid exposure to eyes. Never open the laser
diode box, please refer unit to a qualified engi-
neer for servicing or repairs
OVERVIEW
DMX LASER TRI 160
Green: 532nm 30mW/ Red:650nm 100mW/
Yellow:130mW
Red and green and yellow laser
DMX 512 10 channel
40 pre programmed moving patterns
Sound activated, auto and DMX modes
Static, flat beam and pulse gobo effects
Linkable Master/Slave in sound active,
automatic, DMX
Trigger mode, built in black out with in no sound
Micro step scanning motor
Stand alone mode or DMX 512
Key switch
Endless show creation possibilities
Easy-Mini controller
XLR DMX in and out
DMX connection
DMX INPUT: DMX signal input -
Male XLR
DMX OUTPUT: DMX signal output -
Female XLR
MIC: Sound active
Min-Max: Adjust the sensitivity knob for sound
active
POWER SWITCH: ON/OFF power
FUSE: 3A Fuse
DMX channels functions and options
When using a DMX controller, DIP SWITCH 1~10
setting as follows: NO.1 & NO.10 in
“ON” for control via DMX.
PANEL
(A)
DMX INPUT: DMX signal input----Male XLR
(B)
DMX OUTPUT: DMX signal output----
Female XLR
(C)
MINI CONTROLLER: Use 5-XLR Male
(D)
DIP SWITCH: DMX address
(E)
MIC: Sound active
(F)
MIN-MAX: Adjust the sensitivity knob for
sound active
(G)
POWER SWITCH: ON/OFF power
(H)
KEY: LOCK laser
(I)
MAINS INLET WITH FUSE: 3A F
A
CHANNEL
DMX512 OPTIONS
FUNCTION
1
0~63
Sound active programs
64~127
Automation program (3ch-10ch not available)
128~191
Manual and with sound activation
192~255
Automation and automatic activation
2
0~63
Blackout
64~127
On blanking off
128~191
Pulse
192~255
Off blanking on
3
0~255
Select patterns
4
0~255
gobo moving speed
5
0~63
Keep gobo to static
64~255
Gobo change to flat effect
6
0~63
Keep gobo to static
64~127
Follow the gobo form pulse to fast speed
dotting effect
128~191
Follow the gobo form pulse to middle speed
dotting effect
192~255
Follow the gobo form pulse to slow speed
dotting effect
7
0~63
Keep gobo to static
64~255
Gobo to up and down
8
0~255
Laser effect projection speed.
9
0~255
Control the gobo to zoom
10
0~255
Slow-draw speed, There are 12 mode speeds
to control gobo to slow-draw.
From slowly and fast.
l
When using a DMX controller with the laser select No.1ch to Manual mode or Automation
mode, and select No.2ch to line.
l
When using a DMX controller with the laser, please note No.4ch to 0, speed function doesn't
work. Select No.4ch speed mode function to begin working from small to large. images
B
D
C
E
F
G
H
I
TRI160_manual 12/10/07 11:10 Page 2