Kalkhoff Bosch Cruise User Manual Download Page 249 | Manualshive

Page: 249 / 550

background image

VIII User Manual Pedelec Xion

13

›

Damaged batteries may neither be charged, nor
continue to be used.

›

The battery may heat up during charging.
A maximum temperature of 45°C may be
reached. If the battery becomes any warmer than
this, suspend the charging process immediately.

4.4 Fitting the battery

1. Insert the battery into the battery holder of the Pe-

delec from the front/above. At the same time, the key
must be in the lock and must be turned anticlockwise.

2. Press the battery down into the holder until the lock-

ing mechanism engages. Now turn the key clockwise
and remove it. The battery is now locked in place.

3. Make sure the battery is firmly in place.

Installing the battery

Locking the battery

5 Control panel and display

The Xion Pedelec can be controlled via two elements. The
display is located in the middle of the handlebar. The con-
trol panel can be found on the handlebar grip.

5.1 Control panel

The three buttons each have different functions depending
on the item of the settings menu in which you are located.

5.1.1 Switching on/off

Press the diamond button to switch the Xion system on.
After a few seconds, the welcome screen appears, followed
by the start menu.
From there you can carry out further settings

(

➠

5.4 “Programming and settings”)

.

Control panel and display

1 Upper arrow button

2 Diamond button

3 Lower arrow button

1

2

3

«
...
247
248
249
250
251
...
»

Summary of Contents for Bosch Cruise







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Bosch Cruise

Brand: QU-AX Pages: 44

SPEEDMASTER MC 8

Brand: SIGMA SPORT Pages: 4

Brand: Kidzmotion Pages: 9

Brand: POLKABIKES Pages: 16

Brand: GLOBBER Pages: 20

Brand: GLOBBER Pages: 74

Brand: Cateye Pages: 3

Brand: Cateye Pages: 2

Brand: aventon Pages: 29

Brand: FiSHAW Pages: 18

Brand: ICONE Pages: 80

Brand: Echowell Pages: 2

Spitzing Pedelec

Brand: M1-Sporttechnik Pages: 20

Brand: Exposure Pages: 1

Brand: Hase Spezialräder Pages: 28

Brand: CAMPAGNOLO Pages: 98

Brand: Kinderkraft Pages: 44

Brand: Decathlon Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands