15
KD-070/50 SERIES
KD-070/50 SERIES
KALE ELECTRONIC GLASS DOOR LOCK
KALE ELECTRONIC GLASS DOOR LOCK
Changing the door on the left or right side.
1. Open the battery cover.
2. Insert the screwdriver into the hole.
3. Remove the screws of the installed one.
4. Pull out the front body to remove.
5. Turn it 180 ° and install back with screw.
1. Passcode button
2. Start / End button
3. Card reading section
4. Reset button
5. 9V emergency power terminal
9V emergency power terminal:
In case of battery depletion, you can open the door using a 9V battery.
Reset function:
The temporary program error can be resolved by pushing the reset button with a
pointed object through the hole. (Pin code is not changed by this process)
Card reading section:
Touch your card to the device to open the door.
On / Off button:
Single button is used to open or close the door.
Manual operating device:
Used to open the door manually (for fire or other emergencies)
Fire detection sensor:
The fire detection sensor exists to open the door automatically in case of
fire. (60C±5C)
Lock latch (lock latch counterpart):
Internal connection member of the door lock
Automatic lock internal sensor:
When the automatic lock is set, a magnetic sensor is placed that
locks the door automatically.
Enter button:
Used for passcode entry, registering and card cancellation.
• Registering:
Press the Enter button once and then press any button on the
remote control. The information about the success of the registry is given with the
"Ding dong dang" sound (registering in 8 seconds)
• Delete:
Press the Enter button once and then the "5" button twice. Finally, to
complete, press the "*" button.
* Remote controls can be registered up to 15.
• On / Off
The door opens or closes within 2 ~ 3 seconds after the button is pressed.
*Frequency: FM447.275Mhz * Battery: AAA Size X 2EA (CR2032 1EA)
* Keep the door open when checking and registering the normally registered
passcode.
1. Open the battery cover in the internal body and press the button once. (A
"Beep" sound is heard.)
2. Enter the new passcode. (3 to 19 digits can be registered.)
3. To complete the registration, press the "*" button.
(If the entry is successful, the "ding-dong-dang" sound is heard.)
• Perform before the light goes off to move onto the next stage (Within 15 seconds).
* Register the passcode with the same procedure as stated above.
* When the new passcode is saved, the current password will be automatically
deleted.
• When the door is open, never fail to register or change the passcode.
• The passcode is set as "1234" at the factory. - After installation, change the
passcode prior to using.
1. Open the battery cover in the internal body and press the button once. (A
"Beep" sound is heard.)
2. Touch each card to be registered to the card reading part on the outer body. Up
to 50 cards can be registered.
3. To complete the registration, press the "*" button. If successful, the
"ding-dong-dang" sound is heard. (A "beep" sound on failure.)
• Setup (Glass door lock without the fixing plate)
Installation Tips!
1. Sprinkling a little water on the glass door allows you to make easier installation.
2. Depending on the status of the door, the existence of silicone coating on the door lock may help
prevent slippage.
1. Battery cover
2. Enter button
3. Manual Operation Button
4. On / Off switch
5. Lock Latch
6. Automatic lock internal sensor
Outer Body
Inner Body
14
(Only the applied model)
• Only record the card issued by the manufacturer.
•Registering and using a transportation card or a credit card can lead to security problems,
in this case in the event of any damage, you can not get A/S or receive compensation.
Açma/
Kapama
Butonu
3- PART NAMES
5 - PASSCODE REGISTRATION
6 - PASSCODE CHANGE
7 - CARD REGISTRATION
4- REMOTE CONTROL USE
