Kaisai RG51IJ1BGCE, Manual

Page: 5 / 14

Model
Lowest Voltage of
CPU Emitting Signal
Rated Voltage
8m (when using 3.0 voltage,
it Gets 11m)
3.0V(Dry batteries R03/LR03
×
2)
2.0V
Remote Controller Specifications
1. Operating Mode: AUTO, COOL, DRY, HEAT(Cooling & heating models only)
and FAN.
2. Timer Setting Function in 24 hours.
O O
3. Indoor Setting Temperature range: 17 C~30 C.
4. Full function of LCD (Liquid Crystal Display)
Environment
Signal Receiving
Range
Performance Feature
Function buttons
CAUTIONS
Do not mix old and new batteries or batteries of a different type.
Do not leave the batteries in the remote controller if it is not going
to be used for 2 or 3 months.
Dispose of the old batteries in the special containers to be found
in the sales outlets.
1
TEMP UP Button
Push this button to increase the indoor temper-
ature setting in 1 C increments to 30 C.
2
TEMP DOWN Button
Push this button to decrease the indoor temper-
ature setting in 1 C increments to 17 C.
Each time the button is pressed, the operation
mode is selected in the sequence of the following:
3
MODE Button
3 4
4
DIRECTION/SWING Button
(For RG51Q models)
SWING Button
(For RG51Q(1) models)
6
5
7
RESET Button
Once the recessed RESET button is pressed,
all of the current settings will be cancelled
and the controller will return to the initial settings.
8
ON/OFF Button
Operation starts when this button is pressed
and stops when the button is pressed again.
NOTE: Heat mode is for Cooling & Heating models only.
AUTO COOL DRY HEAT FAN
Used to select the fan speed in four steps:
Auto Low Med High
FAN SPEED Button
NOTE: Med fan speed is not available for RG51J
models .
O O
-5 C~60 C
RG51Q/BG(C)E, RG51J(1)/(C)E, . RG51Q1/BG(C)E, RG51IJ(1)/BG(C)E
RG51Q/BG(C)E
RG51Q1/BG(C)E
ADJUST
ADJUST
AUTO
COOL
DRY
HEAT
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
FAN
HIGH
MED
LOW
MODE
MODE
SWING
SWING
AIR
DIRECTION
FAN SPEED
FAN SPEED
DIRECTION
/SWING
SWING
TIMER ON
TIMER ON
ECO
ECO
ON/OFF
ON/OFF
TIMER OFF
TIMER OFF
RESET LOCK
RESET C/H
2
1
4
5
5
6
3
7
8
9
10
11
SET TEMPERATURE( C)
SET TEMPERATURE( C)
12
Used to stop or start horizontal louver move-
ment or set the desired up/down air flow
direction. The louver changes 6 degree in
angle for each press. If keep pushing more
than 2 seconds, the louver will swing up and
down automatically.
SWING Button
(For RG51Q1 models)
SWING Button
(For RG51J models)
Used to stop or start horizontal louver move-
ment .
Used to stop or start vertical louver move-
ment .
AIR DIRECTION Button
(For RG51Q1models)
Used to set the desired up/down air flow
direction. The louver changes 6 degree in
angle for each press.
Buttons design might be slightly different from the actual one you purchased
depending on individual models.
All the functions described are accomplished by the indoor unit. If the indoor unit
has no this feature, there is no corresponding operation happened when press the
relative button on the remote controller.
Note:
5
kaisai.com