Kaisai FLY, Owner'S Manual

Page: 99 / 198

Example: Setting the unit to turn on after 6 hours, operate for 2 hours, then turn off
(see the figure below)
Your remote display
Current
time 1PM
2PM 3PM 4PM 5PM
6PM 7PM 8PM 9PM
Timer starts
Unit turns Unit turns
ON
OFF
6 hours later
8 hours later
Setting both TIMER ON and TIMER OFF at the same time
Keep in mind that the time periods you set for both functions refer to hours after the
current time. For example, say that the current time is 1:00 PM, and you want the unit
to turn on automatically at 7:00 PM. You want it to operate for 2 hours, then automa-
tically turn off at 9:00 PM.
Do the following:
ON/OFF
ON/OFF
MODE
MODE
SHORT
SHORT
CUT
CUT
TIMER ON
TIMER ON
TEMP
TEMP
3
3
sec
sec
4
8
3
7
X12
X16
2
6
1
5
Timer
Timer
or
or
Timer is set To turn ON
6 hours from current time
Timer is set to turn OFF
8 hours from current time
The follow me function enables the remote
control to measure the temperature at
its current location and
. When using AUTO, COOL, or
HEAT modes, measuring ambient
temperature from the remote control
(instead of from the indoor unit itself)
will enable the air conditioner to
optimize the temperature around you
and ensure maximum comfort.
send this signal
to the air conditioner every 3 minutes
interval
FOLLOW ME function
Silence function
SLEEP Function
O 8 C Heating Function
The SLEEP function is used to decrease
energy use while you sleep (and don t
need the same temperature settings to
stay comfortable). This function can
only be activated via remote control.
Note:
The SLEEP function is not
available in FAN or DRY mode.
,
How To Use The Advanced Functions How To Use The Advanced Functions
The TURBO function makes the unit work
extra hard to reach your present temperature
in the shortest amount of time possible.
When you select TURBO feature in COOL
mode, the unit will blow cool air with
strongest wind setting to jump-start the
cooling process.
When you select TURBO feature in HEAT
mode, for units with Electric heat elements,
the Electric Heater will activate and
jump-start the heating process.
Airborne bacteria can grow in the moisture
that condenses around heat exchanger in
the unit. With regular use, most of this
moisture is evaporated from the unit.
When the self clean feature is activated,
your unit will clean itself automatically.
After cleaning, unit will turn off automatically.
You can use
self clean
feature as often as
you like.
Note: You can only activate this function
in COOL or DRY mode.
SELF CLEAN function
TURBO function
For the detail, see sleep operation in
USER S MANUAL.
,
,,
,,
,,
,,
Hold down Fan button for 2 seconds to
activate/cancel
Silent
mode. Due to low
frequency operation of compressor, it may
result in insufficient cooling and heating
capacity. (applicable to the air conditioner
with Silent feature only)
Mode
Mode
Fan
Fan
Timer
Timer
Timer
Timer
Turbo
ON/OFF
ON/OFF
SWING function
Swing Button
Swing Button
Used to stop or start horizontal louver
movement or set the desired up/down
air flow direction. The louver changes 6
degree in angle for each press. If keep
pushing more than 2 seconds, the louver
will swing up and down automatically.
Used to stop or start vertical louver
movement and set the desired left/right
air flow direction. The vertical louver
changes 6 degree in angle for each
press. If keep pushing more than 2
seconds, the vertical louver auto swing
feature is activated.
Sleep
Sleep
When the air conditioner operates
under heating mode with the set
O temperature of 17 C, press Temp
button twice in one second will
activate 8 Degree heating function.
The unit will operate at a setting
O temperature of 8 C. The indoor
unit display shows FP .
,, ,,
SHORTCUT function
Used to restore the current settings or
resume previous settings.
Push this button when remote controller
is on, the system will automatically revert
back to the previous settings including
operating mode, setting temperature, fan
speed level and sleep feature (if activated).
If pushing more than 2 seconds, the
system will automatically restore the
current operation settings including
operating mode, setting temperature,
fan speed level and sleep feature
(if activated ).
Short
cut
Short
cut
LOCK function
Press Turbo button and Blow button
simultaneously for one second to
lock or unlock the keyboard.
Hold together for one second
to activate LOCK function
Hold down Fan
button for 2
seconds to activate
Silence function
Press this button
twice in one second
O to activate 8 C
heating function
Turbo
Follow
me
Self
clean
LED
Follow
me
Self
clean
LED
EN
80 81