While driving, keep the accelerator steady for a few seconds until Cruise
Control kicks in and scooter travels at constant speed without driver holding
down the accelerator. When you activate the brakes Cruise Control will be
Display Settings
–
Wolf Warrior 35Ah
The Wolf Warrior 35Ah scooter is equipped with the following LCD display:
1.
Speedometer. Shows the speed at which you are travelling.
2.
Battery Indicator. Charge your scooter frequently, do not let it run out
of battery. As a rough guideline, charge at or below 2 bars.
3.
Gear. Shows the selected gear.
4.
Gear selector. Press to set gear (1=slow, 2=medium, 3=fast).
5.
Power Button. To turn the scooter on or
off
press button for 2 seconds.
6.
Accelerator. Pull to accelerate. The stronger you pull, the faster it
accelerates. The scooter is delivered in “Non-Zero Start” setting
(Kick-And-Go is ON), i.e. the accelerator only works if the scooter is
already in motion.
7.
Mode Button. Press to select various display options:
MODE
COMMENT
TIME
Time since powering on the
scooter.
TRIP
Distance travelled since powering on the scooter.
ODO
Total distance travelled.
VOL
Current voltage.
CHA
Number of times battery has been charged (inaccurate as only full
discharges are counted)
Detailed P
-
settings mode.
To access P-settings to make various advanced
changes, press MODE [7] for 2-
3 seconds.
Cycle through the P-settings using the MODE button
[7].
In order to change a
P-
setting press GEAR button [4].
To return to operating mode, wait a few
seconds.
P
-
SETTINGS
P0
Tire diameter (11 = 11 inch). Do not change.
P1
System voltage. Default 60V. Do not change.
P2
Motor magnetic pole setting. Default 15. Do not change.
P3
Speed signal selection. Default is 0. Do not change.
P4
Distance / speed unit. 0=km, 1=miles
P5
Start setting. 1=non
-zero start (Kick-and-Go), accelerator won’t work if scooter not
in motion; 0=immediate start (CAUTION while using this!)
P6
Cruise control. 0=cruise control OFF, 1=cruise control ON. Advanced riders only.
P7
Initial acceleration. 0=strong power, 5=least power.
P8
Speed limit as % of top speed, i.e. 100=no speed limit.
P9
Motor torque. 1=50% of max. torque, 2=75% of max. torque, 3=max. torque
PA
Electric (regenerative) braking strength (E-
ABS). 0=None, 1=Weak, 2=Medium,
3=strong.
PB
Display brightness (0=off, 5=highest illumination)
PC
Scooter auto-
turn off time in minutes (1
-
30 minutes).
PD
ABS (anti-
lock braking system) setting. 0=ABS off, 1=ABS on (as in a car, the brake
engages and disengages rapidly to prevent the wheel from blocking)
WARNING: Due to increased vibration and force and on scooter components when
using ABS, do frequently check that all bolts are properly fastened.
Cruise
Control.
Cruise control allows you to maintain your driving speed auto-
matically without continuing to hold down the
accelerator.
In order to enter
Cruise Control, activate it first in the P
-settings
[P6].
While driving, keep the accelerator steady for 3-5 seconds until Cruise Control
kicks in and scooter travels at constant speed without driver holding down
the
accelerator.
When you activate the brakes, Cruise Control will be
cancelled.
CAUTION: Ride in a position where you can immediately access the
brake to cancel Cruise Control if
necessary.
09
10
