K1EL
WKUSB-AF User Manual
WKUSB-AF
WKUSB-AF User Manual
5/19/2022 Rev 1.0
Page 56
/V
Send the supply voltage in Morse, useful for beacons.
/Wnn
Wait for nn seconds. (nn=00 to 99)
/X
Cancel speed override, for example cancel HSCW, QRSS, or /Snn speed.
/Yn
Force a relative speed change up. Add
n
to the current WPM. n=(0-9)
/Zn
Force a relative speed change down. Subtract
n
from the current WPM. n=(0-9)
/1
Jump to message 1
/2
Jump to message 2
/3
Jump to message 3
/4
Jump to message 4
/5
Jump to message 5
/6
Jump to message 6
IG
Insert ½ letterspace pad
(DI-DI-DAH-DAH-DIT)
IM
Insert
wordspace
pad
(DI-DI-DAH-DAH)
Rate Table
n
HSCW Rate
QRSS Rate
0
1000 lpm (200 wpm)
3 sec dit
1
1500 lpm (300 wpm)
6 sec dit
2
2000 lpm (400 wpm)
10 sec dit
3
3000 lpm (600 wpm)
12 sec dit
4
4000 lpm (800 wpm)
30 sec dit
5
6000 lpm (1200 wpm)
60 sec dit
Embedded Command Examples
/B60BCON DE K1EL BEDFORD NH
send BCON DE K1EL BEDFORD NH every 60 seconds
UR RST IS /P QSL
pause to allow the user to enter the RST then resume automatically
/K05 /W10 VVV DE K1EL
key down for 5 secs, wait 10 secs, and then send VVV DE K1EL
CQ CQ CQ DE /M /M /M
send a 3x3 CQ using the user callsign
/H2CQ CQ DE K1EL K1EL K1EL/S15 DE K1EL
send 1
st
part at 1500 lpm and the 2
nd
at 15 WPM
CQ CQ CQ DE K1/I10TMT/I00 K
send message with 20% extra space in TMT. A more manageable way of
doing this would be to load
K1/I10TMT/I00
in the callsign slot to get this spacing any time /M is used.
CQ CQ CQ DE /Z4K1EL K1EL K1EL/Y4 K
send the callsigns 4 WPM slower then return to normal WPM.
QTH IS /E/C1/E NAME IS STEVE
send the QTH from the alternate message bank and return for the name.
/Q2EL /1
continuously send EL at QRSS10 speed (this message is in slot 1). Avoid inserting a space
between the QRSS command and the start of text: /Q2 EL unless you want a long delay at start of message.
/B10K1EL BCON/W2/VVOLTS
send K1EL BCON, wait 2 secs, send XrXX VOLTS repeat every 10 secs
SOM/E2/C3/E2/U2/W5/U1/S50K1EL//1/XEOM
send SOM, set msg bank 2, call msg 3, set msg bank 1, turn
on PTT for 5 seconds. Change speed to 50 WPM send K1EL/1, cancel 50WPM send EOM.
Standalone Beacon Operation
There are several ways to run a beacon from WK in standalone mode. The first way is to load a message
followed by a delay and jump. This would look like this, loaded into slot one:
K1EL BCON /W12 /1
K1EL BCON will be sent followed by a 12 second delay after which there is a jump back to the beginning.
The second way is to use the embedded beacon command, which is easier:
/B12K1EL BCON