K-TRON KSU-II/KCM Programming Instructions Manual Download

Page: 62 / 121

Programming Reference

1.12Security menu (only KSU-II/KCM)

Page 62

Docu-No.: 0590020601-EN Rev. 1.6.0

1.12

Security menu (only KSU-II/KCM)

This menu sets access for all menus in the KSU-II/KCM.

1.12.1

Security parameters

• The access to the parameter in the security menu can be de-

activated by the data lockout input of the KSU-II/KCM display
(see section

1.12.2

• All programmed security selections (e.g RD/WR) will be de/

activated immediately by programming the ACCESS TYPE.

• Menus marked with * are hidden by default.

Parameter

Definition

PRODUCT CHANGE

CALIBRATION

ALARM*

TUNING*

REFILL*

SCALE*

MACHINE SETUP*

I-O SETUP*

LOADER*

HCU LOADER*

SYSTEM*

FDR BEING VIEWED*

AccessType

Permission

RD/WR

Reading and writing possible.

READ

Read only possible.

HIDE

No access menu. Menu is not visible.

TOTAL KEY

Select: <Clear Only>, <Rd Only>, <Any Num> as entries.

SP ACCESS

Select: RD/WR, Read. Hide.

VOL & ALR CLR

Select: Enable, Disable.

Vol/Alarm when enabled, allows use of the Grav/Vol key and permits
alarms to be acknowledged or cleared.

Summary of Contents for KSU-II/KCM


























































































































Search results

Summary of Contents for KSU-II/KCM

Reviews:

Related manuals for KSU-II/KCM

Brands by name

Popular brands

K-TRON KSU-II/KCM, Programming Instructions Manual

Search results

Summary of Contents for KSU-II/KCM

Reviews:

Related manuals for KSU-II/KCM

Brands by name

Popular brands