K-TRON KSU-II/KCM Programming Instructions Manual Download

Page: 51 / 121

Docu-No.: 0590020601-EN Rev. 1.6.0

Page 51

Programming Reference

I/O Menu 1.8

1.8.3

Setpoint input sub-menu

Refer to manual KCM Electronics for more information.

For calibration, see section

3.2

Parameter

Definition

SOURCE

Analog Input Source

Selection of the desired remote setpoint input for the KCM. Select
CPU_0-10kHz, CPU_Analog, Extern

Notes:

• See KCM Electronics manual for wiring details when selecting

CPU source inputs.

• For Extern function to work, Modbus I-O must be configured first

and the external I-O module (e.g.WAGO) connected via K-Port 2.

• Check the jumper on the KCM CPU for the following possible

choices: 0-5 Vdc, 0-10 Vdc, 0-20 mA if CPU_Analog is the input
selection.

AIN VALUE-[%]

Analog Input Value%

Display of the actual input value in percentage of the maximum
value, AinMax as defined below.

Input range: Display only

AIN MIN-[%]

Analog In Value Min

Scaling of the analog output for the minimum value. (Offset
adjustment e.g. 20% for 4 mA).

This value can be used also to invert the analog input.

Input range: 0 to *100%

*Inverted 100%

AIN MAX-[%]

Analog In Value Max

Scaling of the analog output for the maximum value.

This value can be used also to invert the analog input.

Input range: 100 to *0%

Default: 100%

*Inverted 0%

DEADBAND-[%]

Deadband

Input of the deadband in percentage of the maximum value.
Changes at the input below this value will have no change to the
setpoint value.

Input range: 0 to 100%

Default: 0%

Summary of Contents for KSU-II/KCM


























































































































Search results

Summary of Contents for KSU-II/KCM

Reviews:

Related manuals for KSU-II/KCM

Brands by name

Popular brands

K-TRON KSU-II/KCM, Programming Instructions Manual

Search results

Summary of Contents for KSU-II/KCM

Reviews:

Related manuals for KSU-II/KCM

Brands by name

Popular brands