background image

       

HALOGEN BULBS     

ALWAYS SWITCH OFF THE ELECTRICITY 
SUPPLY BEFORE CARRYING OUT ANY 
OPERATIONS ON THE APPLIANCE.   

To change bulbs:   
1. Rotate the cover in anticlockwise, as shown. 

CAUTION: BULB MAY BE HOT,PLEASE 
ROTATE WHEN THE BULB IS COOL!   

2. Replace with a Type JC, 12Volt, 20Watt 

Max, G-4 Base bulb. Do not touch 
replacement bulb with bare hands! If the 
bulb is touched with the bare hand, it should 
be cleaned with a lint-free cloth moistened 
with methylated spirit.   

 
 
 

LED LIGHTS                       

ALWAYS SWITCH OFF THE ELECTRICITY 
SUPPLY BEFORE CARRYING OUT ANY 
OPERATIONS ON THE APPLIANCE.   

To change the light: 
1. Open the filter and find the spring of the light, 
push the spring and the lgight will be slip out. 
Change the light as with same kind of 4Volt,3 
Watt LED light. CAUTION: LIGHT MAY BE 
HOT,PLEASE ROTATE WHEN THELIGHT IS 
COOL!  

 
 
 
 
 

WARRANTY        

 

We will warrant this product free from defects in material and quality for one year and motor for 
5 years. If any problems occur from correct usage, please contact the service department for 
under warranty service.     
This warranty does not cover the following: 
The filter mesh and bulb. 
Commercial use. 
Amendment of the date of manufacture on the rating plate. 
Damaged caused to the body by usage of detergent sprayer. 
Pollution made to the led parts, glass parts and S/S parts. 
Incorrect installation, misuse, abuse or neglect. 
Incorrectly fitted to insufficient or unsuitable power. 
Taken apart or serviced by unauthorized service engineers or replaced with other manufacture’s 
components. 
For commercial use the maintenance and free service should be discussed with our authorized 
agent. 
Beyond the 12 month limited warranty period, the purchaser should pay for charge of 
components and call out. 
In the event of a service call, please provide the warranty card and receipt of date of purchase.   

 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

 

Summary of Contents for 3388C













Reviews: