4
CAUTION
Do not use the impact dril in the IMPACT mode
if the material can be bored by rotation only. Such
action will not only reduce drill afficiency, but may
also damage the drill tip.
When changing over, ensure the change knob is
slide as far as it will go.
9. High-spped/Low-speed changeover
To change speed, rotate the gear shift lever as
indicated by the arrow in Fig. 8. The numeral “1”
engraved on the drill body denotes low speed, the
numeral “2” denotes high speed.
Fig. 8
PRACTICAL HANDLING PROCEDURES
1. Speed adjustment and switch operation
䡬
The drill speed can be adjusted from 0 through full
speed by regulating the trigger-squeezing force.
The more the trigger is squeezed, the faster the drill
rotates. When the trigger is squeezed fully, the
speed is the maximum.
䡬
Pulling the trigger switch and pushing the stopper,
keeps the switched-on condition which is convenient
for continuous running. When switching off, the
stopper can be disconnected by pulling the trigger
again.
CAUTION
Drill at a maximum rotation speed when drilling
wooden materials.
2. When using as a Drill or an Impact Drill
(1) Pressing force of the drill
You cannot drill holes more quickly even if you
press the drill with a stronger force than necessary.
It not only damages tip of drill bit and decreases
the efficiency of operation, but also shortens the
life of the drill tip.
(2) In case of penetrating holes
Drill bits can be broken when the material being
drilled is penetrated. It is important to decrease
pressing force just before penetrating.
CAUTION
In continuous operation, conduct no-load operation
for five seconds after completing a drilling job.
(3) When a thick drill bit is used
Your arm is subjected to larger reaction force when
a thicker drill bit is used. Be careful not to be moved
by the reaction force. For this, establish a foothold,
hold the unit tightly with both hands perpendicularly
to the material being drilled.
Gear shift lever
3. Using a large diameter drill bit
The larger the drill bit diameter, the larger the
reactive force on your arm. Be careful not to lose
control of the drill because of this reactive force.
To maintain firm control, establish a good foothold,
hold the drill tightly with both hands, and ensure
that the drill is vertical to the material being drilled.
4. When drilling completely through the material
When the drill bit bores completely through the
material, careless handling often results in a bro-
ken, drill bit or damage to the drill body itself due
to the sudden movement of the drill. Always be
alert and ready to release pushing force when drilling
through the material.
MAINTENANCE AND INSPECTION
1. Inspecting the drill bit
Continued use of a worn and/or damaged drill bit
will result in reduced drilling efficiency and may
seriously overload the drill motor. Inspect the drill
bit frequently and replace it as necessary.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure
that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Failure
to do so could result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the
power tool. Exercise due care to ensure the winding
does not become damaged and/or wet with oil or
water.
4. Servicing
Consult an authorized Service Center in the event
of power tool failure.
5. Service parts list
CAUTION
Repair, modification and inspection of K-EIKO Power
Tools must be carried out by an K-EIKO Authorized
Service Center.
This Parts List will be helpful if presented with the
tool to the K-EIKO Authorized Service Center when
requesting repair or other maintenance.
In the operation and maintenance of power tools,
the safety regulations and standards prescribed in
each country must be observed.
MODIFICATIONS
K-EIKO Power Tools are constantly being improved
and modified to incorporate the latest technological
advancements.
Accordingly, some parts may be changed without
prior notice.
NOTE
Due to K-EIKO’s continuing program of research and
development, the specifications herein are subject to
change without prior notice.
