background image

25

Item

Detail

BIOS Information

Includes BIOS version and the date on which the BIOS 

was built

Memory Information

Shows memory size, type and speed as detected by 

the BIOS

ME Information

Indicates the version of the management engine

Board Information

Such as hardware revisions and serial number

System Date & Time

System Date

Changes system date, date must be entered in MM/

DD/YY format

System Time

Changes system time, time must be entered in 

HH:MM:SS format.

Access Level

Displays current access level, default is Administrator

Table  4-2: BIOS Main Setup Menu

4�3    Advanced Setup

Select the Advanced tab from the setup screen to enter the Advanced BIOS Setup screen. 

You can select any of the items in the left frame of the screen, such as SuperIO Configuration, 

to go to the submenu for that item. Display an Advanced BIOS Setup option by highlighting 

it using the < Arrow > keys. The Advanced BIOS Setup options are as follows.

Item

Detail

Legacy OpROM Support

Launch PXE OpROM

Enables or disables legacy network device (default is 

Disabled)

Launch Storage OpROM

Enables/disables the option for Legacy Mass Storage 

Devices with option ROM (default is Enabled)

Clock Spread Spectrum

Enables/disables spread spectrum for clock

WatchDog Timer

Shows whether the WatchDog Timer is enabled 

(default is Disabled)

PCI Subsystem Settings

Allows viewing and configuration of PCI and PCIe 

Subsystem settings

ACPI Settings

Enables/disables AXCPI auto configuration (default is 

Disabled)

CPU Configuration

Displays processor type, speed, system bus speed, etc.

PCI Express Ports Configuration Enables/disables PCI Express ports and configures bus 

and resource padding

SATA Configuration

Sets SATA mode and enables/disables SATA controller

Intel Video Configuration

Sets Intel Video function

USB Configuration

Provides USB support and lists the devices attached to 

the USB port (keyboard, mouse, and one hub)

H/W Monitor

Displays voltages on the backplane connector (+3.3 V, 

+5.0 V, +12 V, 5 VSB, and Vbat)

Summary of Contents for PXI Express PXIe-63975
















































Reviews: