JYTEK PXI Express PXIe-63975 User Manual Download Page 15

Page: 15 / 47

Pin

Signal

Pin

Signal

Pin

Signal

Pin

Signal

TMDS

Data2-

TMDS

Data1-

TMDS

Data0-

Analog

Red

TMDS

Data2+

TMDS

Data1+

TMDS

Data0+

Analog

Green

Shield

Ground

Shield

Ground

Shield

Ground

Analog

Blue

Reserved 12

Reserved 20

Reserved

Analog

HSYNC

Reserved 13

Reserved 21

Reserved

Analog

Ground

DDC Clock 14

+5V

Power

Ground

DDC Data

Ground

TMDS

Clock+

Analog

VSYNC

Hot Plug

Detect

TMDS

Clock-

Table 2-1: DVI-I Pin Assignment

2�3�4 GPIB Connector

The GPIB connector on PXIe-63975 is a micro D-sub 25P connector, controlling external

bench-top instruments. Connection to other instruments requires the ACL-IEEE488-MD1-A

cable. The on-board GPIB controller provides:

•  Full compatibility with IEEE 488 standard
•  Up to 1.5MB/s data transfer rates
•  Onboard 2 KB FIFO for read/write operations
•  Driver APIs compatible with NI-488.2 driver software
•  Connection with up to 14 instruments

Summary of Contents for PXI Express PXIe-63975
















































Search results

Summary of Contents for PXI Express PXIe-63975

Reviews:

Related manuals for PXI Express PXIe-63975

Brands by name

Popular brands

JYTEK PXI Express PXIe-63975, User Manual

Search results

Summary of Contents for PXI Express PXIe-63975

Reviews:

Related manuals for PXI Express PXIe-63975

Brands by name

Popular brands