JVC VF-P116E Service Manual Download Page 9

INSTRUCTIONS

VF-P116      

(A)

VIEWFINDER

For Customer Use:

Enter below the Serial No. which is located
on the top of the body.
Retain this information fo future reference.

Mode No.

VF-P116      (A)

Serial No.

1. Read all of these instructions.
2. Save these instructions for later use.

  3. All warnings on the product and in the operating instructions should

be adhered to.

4. Unplug this appliance system from the wall outlet before cleaning.

Do not use liquid cleaners or aerosol cleaners. Use a damp cloth
for cleaning.

5. Do not use attachments not recommended by the appliance manu-

facturer as they may cause hazards.

6. Do not use this appliance near water – for example, near a bath-

tub, washbowl, kitchen sink, or laundry tub, in a wet basement, or
near a swimming pool, etc.

7. Do not place this appliance on an unstable

cart, stand, or table. The appliance may fall,
causing serious injury to a child or adult, and
serious damage to the appliance.
Use only with a cart or stand recommended
by the manufacturer, or sold with the appli-
ance. Wall or shelf mounting should follow
the manufacturer's instructions, and should
use a mounting kit approved by the manu-
facturer.
An appliance and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause the
appliance and cart combination to overturn.

8. Slots and openings in the cabinet and the back or bottom are pro-

vided for ventilation, and to insure reliable operation of the appli-
ance and to protect it from overheating, these openings must not
be blocked or covered. The openings should never be blocked by
placing the appliance on a bed, sofa, rug, or other similar surface.
This appliance should never be placed near or over a radiator or
heat register. This appliance should not be placed in a built-in in-
stallation such as a bookcase unless proper ventilation is provided.

9. This appliance should be operated only from the type of power

source indicated on the marking label. If you are not sure of the
type of power supplied to your home, consult your dealer or local
power company. For appliance designed to operate from battery
power, refer to the operating instructions.

10. This appliance system is equipped with a 3-wire grounding type

plug (a plug having a third (grounding) pin). This plug will only fit
into a grounding-type power outlet. This is a safety feature. If you
are unable to insert the plug into the outlet, contact your electri-
cian to replace your obsolete outlet. Do not defeat the safety pur-
pose of the grounding plug.

IMPORTANT SAFEGUARDS

PORTABLE CART WARNING

(symbol provided by RETAC)

S3126A

11. For added protection for this product during a lightning storm, or

when it is left unattended and unused for long periods of time,
unplug it form the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due to lightning
and power-line surges.

12. Do not allow anything to rest on the power cord. Do not locate this

appliance where the cord will be abused by persons walking on it.

13. Follow all warnings and instructions marked on the appliance.
14. Do not overload wall outlets and extension cords as this can result

in fire or electric shock.

15. Never push objects of any kind into this appliance through cabinet

slots as they may touch dangerous voltage points or short out parts
that could result in a fire or electric shock. Never spill liquid of any
kind on the appliance.

16. Do not attempt to service this appliance yourself as opening or

removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.

17. Unplug this appliance from the wall outlet and refer servicing to

qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the appliance.
c. If the appliance has been exposed to rain or water.
d. If the appliance does not operate normally by following the op-

erating instructions. Adjust only those controls that are covered
by the operating instructions as improper adjustment of other
controls may result in damage and will often require extensive
work by a qualified technician to restore the appliance to nor-
mal operation.

e. If the appliance has been dropped or the cabinet has been dam-

aged.

f. When the appliance exhibits a distinct change in performance –

this indicates a need for service.

18. When replacement parts are required, be sure the service techni-

cian has used replacement parts specified by the manufacturer that
have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other hazards.

19. Upon completion of any service or repairs to this appliance, ask

the service technician to perform routine safety checks to deter-
mine that the appliance is in safe operating condition.

SPECIFICATIONS

Input signal

: Composite video, 1 V(p-p)

high impedance

CRT

: 38 mm (1.5") diagonal(Black and

white 4:3)

Resolution

: More than 600 lines

Indications

: Tally lamp: Lights up during re-

   cording

                                                     (can be turned ON/

   OFF)

     CRT (alert): BATT: Battery (cam-

     era power) goes down

    REC/ALARM: Tape

    end of VCR

    Abnormal display

Power consumption : 12 V DC, 3.6 W
Operating temperature : –5

°

C to 45

°

C

Mass

: 770 

g

TROUBLESHOOTING

Symptom

No raster. Dark screen.

Tally lamp does not
light up.

Check

Are the brightness and
contrast controls correctly
set?

Is the Tally switch set to ON?

Dimensions: (unit: mm)

VICTOR COMPANY OF JAPAN, LIMITED

®

 is a registered trademark owned by VICTOR COMPANY OF JAPAN, LTD.

®

 is a registered trademark in Japan, the U.S.A., the U.K. and many other countries.

© 2000 VICTOR COMPANY OF JAPAN, LIMITED

Printed in Japan
SC96985

Design and specifications are subject to change without notice.

PEAKING

CONT

BRIGHT

TALLY

ON

OFF

68

78

205

118

195

96

52

.5

45

Summary of Contents for VF-P116E


























Reviews: