JVC SLL TK-C9300UA Instructions Manual Download Page 9

Page: 9 / 16

Mounting the Camera

When mounting the camera on a fixer, pan/tilt and the like, use the camera-

mounting screw hole located on the camera-mounting bracket. (Length of screw: 7

mm or less)

MAX.

Camera-mounting

screw hole

Camera-mounting bracket fastening

screws (x2: M2.6 x 6 mm)

Rotation-preventive

hole

Camera-mounting bracket

Note

Use a camera-mounting screw with a length shorter than 7 mm from the

camera-mounting face. Use camera-mounting bracket fastening screws

with length shorter than 6 mm. Do not use a screw that is longer than the

specified length. It may damage the internal parts.

Mounting the Camera-Mounting Bracket on Top of the Camera

The camera-mounting bracket is originally mounted at the bottom of the camera

before shipment but it can also be mounted on top of the camera.

Remove the camera-mounting bracket fastening screws (x2).

The camera-mounting bracket is removed from the camera.

Mount the camera-mounting bracket on top of the camera.

Mount the camera onto a fixer, pan/tilt unit and the like.

BF LOCK

Camera-mounting

bracket fastening

screws

Camera-mounting

bracket

POWER

IRIS

Connection/Installation

Summary of Contents for SLL TK-C9300UA

















Search results

Summary of Contents for SLL TK-C9300UA

Reviews:

Related manuals for SLL TK-C9300UA

Brands by name

Popular brands

JVC SLL TK-C9300UA, Instructions Manual

Search results

Summary of Contents for SLL TK-C9300UA

Reviews:

Related manuals for SLL TK-C9300UA

Brands by name

Popular brands