manualshive.com logo in svg

JVC MX-J770V, Service Manual

Share
Download
JVC MX-J770V Service Manual Download Page 12

MX-J770V/MX-J880V

1-12

Power switch board (See Fig.20)

Remove the two screws W attaching the power 
switch board. Unsolder FW951 on the power switch 
board and disconnect the harness extending to the 
bass-level regulator board.

Eject switch board (See Fig.20)

Remove the four screws X attaching the eject switch 
board. Unsolder FW850 on the eject switch board 
and disconnect the harness extending to the main 
volume & headphone board.

Remote control port board (See Fig.20)

Remove the screw Y attaching the remote control 
port board.

1.

1.

1.

Prior to performing the following procedure, remove 
the metal cover and CD changer mechanism 
assembly.

There is no need to remove the front panel 
assembly.

Disconnect the harness from connector CN900 and 
CN901 on the relay board on the back of the rolling 
panel assembly.

Disconnect the card wire from connector CN905 and 
CN906 on the relay board on the back of the rolling 
panel assembly.

Remove the screw Z attaching the relay board. 
Remove the relay board from the groove i.

Remove the screw A attaching the fixing board and 
remove the fixing board from the groove j.

1.

2.

3.

4.

Removing the relay board and fixing 
board                                      (See Fig.21)

Y

Remote control port board

Power switch board

Eject switch

 board

X

X

W

FW951

FW850

Fig.20

Fig.21

Rolling panel assembly

CN905

Z

A

Groove i

CN900

CN901

Relay board

Groove j

Fixing board

Bass-level        
regulator board

Main volume &     

headphone board

CN906

Summary of Contents for MX-J770V




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands