JVC MX-GT91R Page 11 Service Manual Download

Page: 11 / 85

MX-GT91R

1-11

Prior to performing the following procedure, remove
the metal cover, the CD changer mechanism
assembly and the rear panel.

Remove the tow tie band attaching the wire to the
ampkifer board and voltage board.

Disconnect the wires from connector CN703, CN704
and CN706 on the amplifier board respectively.

Disconnect connector CN215 on the amplifier board
and CN216 on the voltage board from the regulator
board (The heat sink and heat sink bracket will be
detached at once).

Remove the four screws

attaching the amplifier

board to the heat sink.

Remove the two screws

, the board bracket and

the voltage board.

Removing the amplifier board / voltage
board / heat sink (See Fig.19 to 21)

Prior to performing the following procedure, remove
the metal cover, the CD changer mechanism
assembly and the rear panel.

Disconnect the wire from connector CN250 on the
power supply board.

Move the power cord stopper upward and pull out it
from the base chassis.

Disconnect the wire from connector CN218 on the
power supply board.

Remove the power supply board from the CN213 on
the r

egulator board.

Removing the power cord / power supply
board (See Fig.19)

Fig.19

Fig.20

Amplifier board

CN704
CN706

CN216

Regulator board

CN215

Tie band

CN703

Voltage board

Amplifier board

Heat sink

Voltage

board

Voltage board

Fig.21

CN218

Power supply
board

CN250

Power cord
stopper

Base chassis

Power
cord

CN213

Tie band

Summary of Contents for MX-GT91R






















































































Search results

Summary of Contents for MX-GT91R

Reviews:

Related manuals for MX-GT91R

Brands by name

Popular brands

JVC MX-GT91R, Service Manual

Search results

Summary of Contents for MX-GT91R

Reviews:

Related manuals for MX-GT91R

Brands by name

Popular brands