7
2 Preparation
Thank you
for purchasing your new JVC TV.
Your new TV has many features and incorporates the latest technology to enhance your viewing
experience. We recommend that you spend some time reading this instruction manual so that you fully
understand these features. You will also find some hints and tips to help you resolve any issues.
Read all the safety instructions carefully before use and keep this instruction manual for future reference.
Chapter
2
Unpacking the TV
Remove all packaging from the TV. Retain the packaging. If you dispose of it please do so according to local regulations.
The following items are included:
Remote Control /
AAA Batteries x 2
Instruction Manual
Quick Start Guide
Instruction Manual
65" LED Smart 4K HDR TV
LT-65C898
GB
Quick Start Guide
65" LED Smart 4K HDR TV
LT-65C898
Thank you
for purchasing your new JVC TV.
Your new TV incorporates the latest technology to enhance your viewing
experience. We would suggest that you allow about 15 mins for initial setup.
Please follow this guide for a successful first time installation.
The latest eco-friendly power-saving technology will switch off the TV if
it is left on and idle for 4 hours. Please refer to “Auto Standby” under the
“Time Settings” section of the instruction manual for more detail.
Remove all packaging from the unit. Retain the packaging. If you dispose of it please do so according to any local regulations.
TV
Stand Neck
Stand Base
Remote Control/
AAA Batteries x2
Neck Screws (A) x 4
Base Screws (B) x 4
Instruction Manual
Quick Start Guide
Please inspect your TV for damage after unpacking. If
you do notice any damage please consult your dealer.
1. Slide open the battery compartment on the back of the remote control.
2. Insert two AAA size batteries. Make sure to match the (+) and ( - ) ends of
the batteries with the (+) and ( - ) ends indicated in the battery compartment.
3. Slide the battery compartment cover back into place. Make sure it clicks into place.
Attaching the Neck
1. Ensure the TV is switched off and not connected to the
mains power supply.
2. Keep the protective bag on the TV to protect it. You may
need to cut the protective bag before fitting the stand.
3. Make sure you have some help, this requires 2 people.
Lay the TV down on a flat surface ideally on the edge of a
table so the base of the TV slightly overhangs the edge of
the table, with the back side facing up. Please make sure a
soft cushioned material (such as a dry bath towel or thick
piece of foam) is placed beneath the screen. Be very careful
not to knock the edges of the TV, the screen is very fragile.
The LCD display is very fragile, and must be protected at all times when installing and removing the base stand. Be sure that no hard or sharp object, or
anything that could scratch or damage the LCD display, comes into contact with it. DO NOT exert pressure on the front of the TV at any time because the
screen could crack.
• Do not connect the TV to the mains supply until you have completed all the connections.
• Always disconnect the TV from the mains socket when not in use for a long period of time.
• The button on the remote control is only used for switching the TV into standby, it does not disconnect the TV from the mains power.
To completely disconnect the mains power, please remove the mains plug from the mains socket.
1. Connect one end of the RF coaxial cable to the aerial socket on the wall and the other end of the cable to the ANT socket on the back of your TV.
2. Plug the TV into a mains socket and switch on at the mains.
3. In standby mode, press the button on the remote control to turn the TV on. The LED indicator will flash for a few seconds then the TV will switch on.
RF coaxial cable
(not included)
Router
(not included)
LAN
VGA
ANT.
HDMI 1
Optic.OUT
Optional
If you want to connect to the internet via a wired connection
then connect your ethernet cable to the LAN socket.
Setup in
15mins
3
2
What’s in the Box?
Operating Your Remote Control
Installing the Base Stand
1
4
Connecting the Aerial and Turning on the TV
Table
Cushioned
material
Protective
Bag
4 x
Screw (A)
4 x
Screw (B)
4. Attach the neck using 4 x screws (A).
Fitting the Base
5. Attach the base using 4 x screws (B). Be careful when
attaching the base its heavy.
If you don't have a table big enough, you can use the TV
box. Lie the box flat, make sure you place the polystyrene
back in the box first to give the box some rigidity and
strength.
JVC 65' LED Smart 4K HDR TV LT-65C898 Quick Start.indd 1-3
11/02/2019 15:34
Neck screws(A) x4
LANG.
EXIT
LANG.
G
BACK
TV Stand Base
Base screws(B) x4
TV Stand Neck
TV
JVC 65' LED Smart 4K HDR TV LT-65C898 Manual.indd 7
18/02/2019 10:03
