JVC LT-52X579 - 52" LCD TV Service Manual Download Page 16 | Manualshive

Page: 16 / 16

JVC LT-52X579 - 52

(No.YA654<Rev.001>)

VPT

Printed in Japan

SECTION 5

TROUBLESHOOTING

5.1

SELF CHECK FUNCTIONS

5.1.1 OUTLINE

This model has a self check function given below. When an abnormality has been detected, the power is turned off and the POWER LED
flashes to inform of the failure. An abnormality is detected by the signal input state of the control line connected to the microcomputer.

5.1.2 SELF CHECK ITEMS

5.1.3 METHOD OF DISPLAY WHEN A RASTER IS NOT OUTPUT

In the state where a raster is not output by breakdown of the set, an error is displayed by blink of the POWER LED.

<Explanation of operation>

If an error is detected, the power is turned off.
Shortly after the power is turned off, the POWER LED will be blinked.
Power cannot be turned on until the power cord takes out and inserts, after the power is turned off.

Detection item

Detection content

Diagnosis

signal (line)

Detection timing

Low bias line
short protection

Confirm the operation of the low bias (3.3V/5V/
12V/24V) protection circuit.
3.3V:

Q7004

[SIGNAL PWB]

5V:

Q7003

[SIGNAL PWB]

12V:

Q7001

[SIGNAL PWB]

24V:

IC7019

[SIGNAL PWB]

LB_PRO

At 10 seconds after the power is turned on, the
self-check function starts. If NG is detected during
3000ms, the power is turned off automatically.

Type of error

POWER LED flash cycle

Low bias line short protection

LED turning on and off at 2 seconds intervals.

Victor Company of Japan, Limited

Display Division 12, 3-chome, Moriya-cho, Kanagawa-ku, Yokohama-city, Kanagawa-prefecture, 221-8528, Japan

«
...
14
15
16

Summary of Contents for LT-52X579 - 52" LCD TV

















Reviews:

No comments