JVC LT-26KM18/NSK Service Manual Download Page 16

Page: 16 / 20

1-16 (No.YA655<Rev.001>)

4.4.5 ADJUSTMENT MODE

This mode is used to adjust the VIDEO CIRCUIT.

4.4.5.1

HOW TO ENTER THE ADJUSTMENT MODE

When the SERVICE MENU SCREEN of SERVICE MODE is
displayed, press

[1]

key to enter the ADJUSTMENT MODE.

NOTE:

• When a number key other than the

[1]

key is pressed in the

SERVICE MODE SCREEN, the other relevant screen may
be displayed.
This is not used in the adjustment procedure. Press the

[MENU]

key to return to the SERVICE MODE SCREEN.

4.4.5.2

DESCRIPTION OF STATUS DISPLAY

(1) SIGNAL SYSTEM

The signal displayed on the screen is displayed.

(2) ZOOM MODE

State of the ZOOM MODE is displayed.

(3) PICTURE MODE

State of the PICTURE MODE is displayed.

(4) WHITE BALANCE MODE

State of the WHITE BALANCE MODE is displayed.

(5) SETTING ITEM No.

State of the Setting Item No. are displayed.

(6) SETTING ITEM NAME

Setting item name are displayed. The setting item numbers to
be displayed are listed below.

(7) SETTING VALUE (DATA)

The SETTING VALUE is displayed.

PAL50

: PAL50Hz

PAL60

: PAL60Hz

SECAM

: SECAM

NTSC3

: NTSC3.58

NTSC4

: NTSC4.43

525I

: 525i

525P

: 525p

625I

: 625i

625P

: 625p

750P5

: 750p 50Hz

750P6

: 750p 60Hz

1125I5

: 1125i 50Hz

1125I6

: 1125i 60Hz

1125P5

: 1125P 50Hz

1125P6

: 1125P 60Hz

---

: Others

HXGA

: HDMI XGA

SERVICE MODE SCREEN

Press [1] key

(1)SIGNAL SYSTEM (2)ZOOM MODE

(7)SETTING VALUE (DATA)

(5)SETTING ITEM No.

(6)SETTING ITEM

(4)WHITE BALANCE

(3)PICTURE MODE

S001 R DRIVE MID

128

NTSC3 FULL STD

ADJUST MODE SCREEN

SERVICE MENU Ver.XXX
1. ADJUST

2. SELF CHECK

3. I2C STOP

PCVGA

: PC VGA/60

PCXGA

: PC XGA/60

PCSXGA

: SXGA/60

PCSVGA

: PC SVGA/60

PCWXGA

: WideXGA(1360)/60

H525I

: HDMI 525i

H525P

: HDMI 525p

H625I

: HDMI 625i

H625P

: HDMI 625p

H750P5

: HDMI 750p 50Hz

H750P6

: HDMI 750p 60Hz

H125I5

: HDMI 1125i 50Hz

H125I6

: HDMI 1125i 60Hz

H125P5

: HDMI 1125P 50Hz

H125P6

: HDMI 1125P 60Hz

FUL

: FULL

PAN

: PANORAMIC

16Z

: 16:9 ZOOM

14Z

: 14:9 ZOOM

REG

: REGULAR

STD

: Standard

BRI

: Bright

SOFT

: Soft

: Cool

: Mid

: Warm

Setting mode

Setting items

Settings

1.ADJUST

R DRIVE MID

Do not adjust

G DRIVE MID

Adjust (Do not over 128)

B DRIVE MID

Adjust (Do not over 128)

R DRIVE COOL Do not adjust
G DRIVE COOL Do not adjust
B DRIVE COOL Do not adjust
R DRIVE WARM Do not adjust
G DRIVE WARM Do not adjust
B DRIVE WARM Do not adjust

Summary of Contents for LT-26KM18/NSK





















Search results

Summary of Contents for LT-26KM18/NSK

Reviews:

Related manuals for LT-26KM18/NSK

Brands by name

Popular brands

JVC LT-26KM18/NSK, Service Manual

Search results

Summary of Contents for LT-26KM18/NSK

Reviews:

Related manuals for LT-26KM18/NSK

Brands by name

Popular brands