JVC KD-SX1000R Instructions Manual Download Page 46

Page: 46 / 47

AUDIO AMPLIFIER SECTION

Maximum Power Output:

Front: 40 watts per channel
Rear: 40 watts per channel

Continuous Power Output (RMS):

Front: 16 watts per channel into 4

Ω

, 40

to 20,000 Hz at no more than
0.8 % total harmonic distortion.

Rear: 16 watts per channel into 4

Ω

, 40

to 20,000 Hz at no more than
0.8 % total harmonic distortion.

Load Impedance: 4

Ω

(4 to 8

Ω

allowance)

Tone Control Range:

Bass: ±10 dB at 100 Hz
Treble:±10 dB at 10 kHz

Frequency Response: 40 to 20,000 Hz
Signal-to-Noise Ratio: 70 dB
Line-In Level/Impedance: 1.5 V/20 k

Ω

Line-Out Level/Impedance:4.0 V/20 k

Ω

load

(full scale)

Output Impedance: 1 k

Ω

TUNER SECTION

Frequency Range:

FM: 87.5 to 108.0 MHz
AM: (MW) 522 to 1,620 kHz

(LW) 144 to 279 kHz

[FM Tuner]
Usable Sensitivity: 11.3 dBf (1.0 µV/75

Ω

)

50 dB Quieting Sensitivity:

16.3 dBf (1.8 µV/75

Ω

)

Alternate Channel Selectivity (400 kHz):

65 dB

Frequency Response: 40 to 15,000 Hz
Stereo Separation: 30 dB
Capture Ratio: 1.5 dB

[MW Tuner]
Sensitivity: 20 µV
Selectivity: 35 dB

[LW Tuner]
Sensitivity: 50 µV

CD PLAYER SECTION

Type: Compact disc player
Signal Detection System: Non-contact optical

pickup (semiconductor laser)

Number of channels: 2 channels (stereo)
Frequency Response: 5 to 20,000 Hz
Dynamic Range: 96 dB
Signal-to-Noise Ratio: 98 dB
Wow and Flutter: Less than measurable limit

GENERAL

Power Requirement:
Operating Voltage: DC 14.4 volts (11 to 16

volts allowance)

Grounding System: Negative ground
Dimensions (W x H x D)

Installation Size:

182 x 52 x 150 mm

Panel Size: 188 x 58 x 14 mm

Mass: 1.4

(excluding accessories)

Design and specifications subject to change
without notice.

SPECIFICATIONS

EN44-46.KD-SX1000R[E]/1

98.6.5, 5:55 PM

Summary of Contents for KD-SX1000R
















































Search results

Summary of Contents for KD-SX1000R

Reviews:

Related manuals for KD-SX1000R

Brands by name

Popular brands

JVC KD-SX1000R, Instructions Manual

Search results

Summary of Contents for KD-SX1000R

Reviews:

Related manuals for KD-SX1000R

Brands by name

Popular brands