JVC KD-SHX705 Service Manual Download Page 28

Page: 28 / 67

1-28 (No.MA048)

4.2.2 Detailed CD error code

Error

Details of error

Error code

Detailed error code

Focus serch error

Focus is not adjusted by
3-round focus serch

When foucus is not adjusted by
3-round(1set) focus serch after
disc change or focus shock,
the result is NG

81H

0053

0054

0055

0056

0057

0058

0059

0060

0061

0062

0063

0064

Tracking balance adjustment error

Time over(1s)

Tracking balance adjustment is
not finished 1s after adjustment
command(TBA) is executed

TOC area search error

Time over(10s)

TOC area search is not finished
after 10s

Focus balance adjustment error
Time over(2s)

Foucus gain adjustment error is not
finished 0.6s after the adjustment
command(FGA) is executed

Focus balance adjustment is
not finishied 2s after the adjustment
command(FBA) is executed

Focus gain adjustment error

Time over(0.6s)

Tracking gain adjustment error

Time over(0.6s)

Tracking gain adjustment error
is not finished 0.6s after the
adjustment command(TGA) is
executed

TOC read error

Time over(30s)

TOC read operation is not
finished after 30s

1st track access error

Time over(10s)

1st track access is not finished
10s after TOC reading is finished

Last track access error

Time over(10s)

Last track access is not finished
10s after 1st track in running mode

Q code read error

Time over(0.6s)

Q code is not read for 0.6s during
playback of TOC and program
area

TEXT data read error

ALL TEXT data are not read

RF read error

RF is not read
RFOK is recognized as L

82H

80H

82H

84H

80H

81H

Summary of Contents for KD-SHX705




































































Search results

Summary of Contents for KD-SHX705

Reviews:

Related manuals for KD-SHX705

Brands by name

Popular brands

JVC KD-SHX705, Service Manual

Search results

Summary of Contents for KD-SHX705

Reviews:

Related manuals for KD-SHX705

Brands by name

Popular brands