background image

4

 

Connecting the external amplifiers and/or subwoofer / 

連接至外部功率放大器和

 / 

或重低音揚聲器

You can connect amplifiers to upgrade your car stereo system. 
•  Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it 

can be controlled through this unit.

•  Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker 

leads of this unit unused.

*

3

  Remote lead

*

4

  Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint 

(if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit.

*

5

  Signal cord (not supplied for this unit)

您可以連接功率放大器以提昇尊車的音響系統。

• 

將遙控導線(藍色帶有白色條紋)和其他裝置上的遙控導線連接起來,以便可以經由本機進行
遙控。

• 

將揚聲器和本機拔開,再接上功率放大器。將本機的揚聲器接線放置不用。

*

3

 

遙控導線

*

4

 

將地線與金屬車體或者汽車底盤緊密連接,連接處應該沒有被油漆覆蓋(如果已塗上油漆,在連接電
線前,將油漆刮去)。如果不這樣做,可能會損壞本機。

*

5

 

信號電纜(不隨本機提供)

B

Rear speakers

後置揚聲器

Remote lead (blue with white stripe)

遙控導線(藍色帶有白色條紋)

To the remote lead of other 
equipment or automatic 
antenna if any

連接至其他裝置上的遙控
導線或自動天線(若有
裝設)

Y-connector (not supplied for this unit)
Y-

型連接導線(不隨本機提供)

Front speakers

前置揚聲器

JVC Amplifier

JVC 

功率放大器

TROUBLESHOOTING

•  The fuse blows.

*

  Are the red and black leads connected correctly?

•  Power cannot be turned on.

*

  Is the yellow lead connected?

•  No sound from the speakers.

*

  Is the speaker output lead short-circuited?

•  Sound is distorted.

*

  Is the speaker output lead grounded?

*

  Are the “–” terminals of L and R speakers grounded in common?

•  Noise interfere with sounds.

*

  Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?

•  This unit becomes hot.

*

  Is the speaker output lead grounded?

*

  Are the “–” terminals of L and R speakers grounded in common?

•  This unit does not work at all.

*

  Have you reset your unit?

故障排除

• 

保險絲燒斷。

*

 

檢查紅色導線接頭和黑色導線接頭是否接觸正確?

• 

電源不能接通。

*

 

檢查黃色導線接頭是否接上?

• 

揚聲器沒有聲音。

*

 

檢查揚聲器輸出導線接頭是否短路?

• 

聲音失真。

*

 

檢查揚聲器輸出端子是否接地?

*

 

檢查揚聲器的左(

L

)、右(

R

)端子的負極(

)是否共同接地?

• 

噪音干擾音響。

*

 

後接地端子與車身是否使用較短和較厚的電線連接?

• 

本機發熱。

*

 

檢查揚聲器輸出端子是否接地?

*

 

檢查揚聲器的左(

L

)、右(

R

)端子的負極(

)是否共同接地?

• 

本機完全不能操作。

*

 

您是否已經重置您的機組?

Set “L/O MODE” to “SUB.W” (See 
page 13 of the INSTRUCTIONS.)

將“

L/O MODE

”設定為

SUB.W

”(參閱使用說明書

的第

 13 

頁。)

You can also connect a subwoofer to 
the REAR LINE OUT terminals.

您也可以將重低音揚聲器連接至

 REAR 

LINE OUT 

端子。

Set “L/O MODE” to “REAR” (See page 
13 of the INSTRUCTIONS.)

將“

L/O MODE

”設定

為“

REAR

”(參閱使用說明書

的第

 13 

頁。)

You can connect a power amplifier for 
rear speakers.

您可為後置揚聲器連接功率放大器。

 or

JVC Amplifier

JVC 

功率放大器

Subwoofer

重低音揚聲器

JVC Amplifier

JVC 

功率放大器

Front speakers

前置揚聲器

Install3-4_KD-G646_009A_4.indd   4

Install3-4_KD-G646_009A_4.indd   4

2007.10.30   10:25:15 AM

2007.10.30   10:25:15 AM

Summary of Contents for KD-G645



























Reviews: