JVC KD-G501 Service Manual Download Page 9

Page: 9 / 57

(No.MA038)1-9

3.1.7 Removing the CD mechanism assembly

(See Fig. 8)

• Prior to performing the following procedure, remove the front

panel assembly, bottom cover, front chassis assembly, side
panel, rear bracket and main board .

(1) Remove the three screws

attaching the CD mechanism

assembly.

(2) Take out the CD mechanism assembly.

Fig.8

3.1.8 Removing the front board

(See Figs.9 to 11)

• Prior to performing the following procedure, remove the front

panel assembly.

(1) Remove the four screws

on the back side of the front

panel assembly. (See Fig.9.)

(2) Release the ten joints

. (See Fig.10.)

(3) Release the joint

and take out the front board. (See

Fig.11.)

Fig.9

Fig.10

Fig.11

CD mechanism assembly

Top chassis

Rear cover

Joints

Front board

Spring

Front panel assembly

Summary of Contents for KD-G501


























































Search results

Summary of Contents for KD-G501

Reviews:

Related manuals for KD-G501

Brands by name

Popular brands

JVC KD-G501, Service Manual

Search results

Summary of Contents for KD-G501

Reviews:

Related manuals for KD-G501

Brands by name

Popular brands