background image

3

ENGLISH

Attention:

This symbol is
only valid in the
European
Union.

Information for Users on Disposal of Old Equipment

[European Union]

This symbol indicates that the electrical and electronic equipment should not be
disposed as general household waste at its end-of-life. Instead, the product should
be handed over to the applicable collection point for the recycling of electrical and
electronic equipment for proper treatment, recovery and recycling in accordance
with your national legislation.

By disposing of this product correctly, you will help to conserve natural resources
and will help prevent potential negative effects on the environment and human
health which could otherwise be caused by inappropriate waste handling of this
product. For more information about collection point and recycling of this product,
please contact your local municipal office, your household waste disposal service
or the shop where you purchased the product.

Penalties may be applicable for incorrect disposal of this waste, in accordance with
national legislation.

(Business users)

If you wish to dispose of this product, please visit our web page
www.jvc-europe.com to obtain information about the take-back of the product.

[Other Countries outside the European Union]

If you wish to dispose of this product, please do so in accordance with applicable
national legislation or other rules in your country for the treatment of old electrical
and electronic equipment.

01_EN_LCT1973-01A-3b.p65

05.10.25, 20:59

3

Summary of Contents for IF-CF01CMG















Reviews: