background image

EN 

29

JOG

SHUTTLE

+

POWER

MENU

Select The Soundtrack

Your VCR can record two soundtracks simultaneously (Normal
and Hi-Fi) and play back the selected one, or both together. Or,
when viewing a pre-recorded tape that contains two separate
Hi-Fi audio programs, you can choose to listen to either one by
selecting either "Hi-Fi L" or "Hi-Fi R" in step 3.

ACCESS MAIN MENU

SCREEN

1

Press MENU.

ACCESS FUNCTION SET

SCREEN

2

Move the highlight bar (arrow) to "FUNCTION SET" by
pressing CH

5∞

 or TIME SCAN 

%fi

, then press OK or

TIME SCAN 

#

.

SELECT AUDIO MONITOR

SET MODE

3

Move the highlight bar
(arrow) to "AUDIO
MONITOR" by pressing
CH 

5∞

 or TIME SCAN

%fi

, then press OK or

TIME SCAN 

#

 to select the

desired mode:
a– Hi-Fi
b– Hi-Fi L
c– Hi-Fi R
d– Normal
e– Mix

RETURN TO NORMAL

SCREEN

4

Press MENU.

NOTES:

If the tape being played back has no Hi-Fi soundtrack, the
Normal soundtrack will be heard no matter what choice you
make in step 3.

If RF connection is used for TV, even if Hi-Fi audio monitor is
selected the sound will be mono and will be reproduced in
both loudspeakers.

1

2

3

4

5

6

7

8

9

0

2

4

1

3

OK

MENU

TIME SCAN

PREVIOUS PAGE

=

AUDIO MONITOR

HI-FI

S-VHS MODE

ON

AV COMPU-LINK

ON

VIDEO CALIBRATION

ON

TIMESCAN AUDIO

ON

REAR AUX INPUT

VIDEO

NEXT PAGE
SELECT WITH (

5

,

) AND (OK)

PRESS (MENU) TO END

FUNCTION

=

AUTO TIMER

OFF

SUPERIMPOSE

ON

AUTO SP

=

EP TIMER

OFF

DIGITAL R3

ON

VIDEO STABILIZER

OFF

2ND AUDIO RECORD

OFF

NEXT PAGE
SELECT WITH (

5

,

) AND (OK)

PRESS (MENU) TO END

MENU

OK

CH

Summary of Contents for HR-S7500EK













































































Reviews: