10
Specifications
Format ................................ VHS Standard
Video recording system ..... Rotary, slant azimuth two-head
helical scan system
Rotary heads ...................... 2 video heads
RF output ........................... System G/K type modulation
UHF ch 32 – 40 adjustable (preset
ch 36)
Recording (line input) ......... PAL, SECAM (MESECAM tape)
NTSC 3.58, NTSC 4.43
Playback (line output) ........ PAL, SECAM (MESECAM tape)
NTSC 3.58
NTSC 4.43
Simulated PAL (NTSC tape)
Video
Line input level ................. 0.5 – 2.0 Vp-p/75 ohms, unbal-
anced
Line output level ............... 1.0 Vp-p/75 ohms, unbalanced
S/N ratio ........................... More than 45 dB
Horizontal resolution ........ More than 250 lines
(PAL/MESECAM)
More than 220 lines (NTSC)
Audio
Line input level ................. –8 dBm/50 k ohms, unbalanced
Line output level ............... –6 dBm/1 k ohm, unbalanced
Frequency response ........ 100 Hz to 10,000 Hz
Recording/Playback time
CCIR ................................ 240 min. with E-240 cassette
NTSC ............................... 160 min. with T-160 cassette
FF, REW time .................... Approx. 2 min. 30 sec. with E-180
cassette
Power requirements
Rating .............................. AC 110 – 240 V, 50/60 Hz
Operating ......................... AC 90 – 260 V, 50/60 Hz
Power consumption ........... 13 W
Operation temperature ....... 5
°
C to 40
°
C
Dimensions ........................ 360 (W)
×
94 (H)
×
276 (D) mm
Weight ................................ 3.4 kg
Standard accessories
Remote control unit ............................................................... 1
Batteries for remote control ................................................... 2
RF antenna cable .................................................................. 1
Conversion plug .................................................................... 1
•
Design and specifications subject to change without notice.
Troubleshooting
Problem
No power
Tape cannot be ejected
No picture
No colour
Shuttle search does not
function
Disturbances in playback
picture
Remote control does not
function
Auto playback does not
function
Recording does not func-
tion
The video cassette player
does not function properly
Check point
Is the power cord plugged
in?
Is the power turned on?
Was the video cassette
player’s
§
button pressed?
Is the TV set to the video
channel?
Is a cassette loaded?
Are the connections correct?
Set the Colour System Out-
put switch according to the
recorded tape system.
When playing a MESECAM
tape, select the NTSC 4.43
mode.
Is the video cassette player
in the playback mode?
Is tracking adjusted properly?
Is the TV adjusted properly?
Install this VCP a little way
apart from the TV set.
The batteries are weak.
Replace the batteries.
The video cassette’s record-
ing safety tab has not been
removed.
Are the connections correct?
Was the Record button
pressed?
The video cassette’s record-
ing safety tab is removed.
Microcomputer malfunction.
Disconnect the power plug
from the AC outlet and then
re-insert it.
The microcomputer will be
reset to its initial mode.
About Head cleaning
7
If the picture playback becomes blurred, it does not mean
that the recorded program has been erased.
7
Dirt accumulated on the video heads after long periods of
use causes such troubles. In this case, head cleaning
requiring highly technical care is necessary.
7
For head cleaning, consult the nearest JVC dealer.
Summary of Contents for HR-P41A
Page 11: ...11 MEMO ...
