background image

Page 16

April 16, 2002 1:42 pm

Specifications   

*Not provided in certain areas.

Specifications shown are for SP mode unless specified otherwise.
E. & O.E. Design and specifications subject to change without 
notice.

GENERAL

Power requirement

Rating

: AC 110 V – 240 V

d

, 50 Hz/60 Hz

Operating

: AC 90 V – 260 V

d

, 50 Hz/60 Hz

Power consumption

: 14 W

Temperature

Operating

: 5°C to 40°C

Storage

: –20°C to 60°C

Operating position

: Horizontal only

Dimensions (W x H x D) : 360 mm x 94 mm x 247 mm
Weight

: 3.0 kg

Format

: VHS standard

Maximum recording time

(SP)

: 240 min. with E-240 video cassette 

(PAL/MESECAM)

: 160 min. with T-160 video cassette 

(NTSC)

(LP)

: 480 min. with E-240 video cassette 

(PAL/MESECAM)

(EP)

: 480 min. with T-160 video cassette 

(NTSC)

VIDEO/AUDIO

Signal system

: PAL-type colour signal and CCIR 

monochrome signal, 625 lines 
50 fields

: NTSC colour and EIA monochrome 

signals, 525 lines/60 fields

Recording system

: DA-4 (Double Azimuth) head helical 

scan system

Signal-to-noise ratio

: 45 dB

Horizontal resolution

: 250 lines (PAL/MESECAM)
: 220 lines (NTSC)

Frequency range

: 70 Hz to 10,000 Hz

Input/Output

: RCA connectors (IN x 2, OUT x 1)

TUNER/TIMER

TV channel storage 
capacity

: 99 positions (+AUX position)

Tuning system

: Frequency synthesized tuner

Channel coverage

VHF

: (Low) 42 MHz – 175 MHz

(High)175 MHz – 470 MHz

UHF

: 470 MHz – 870 MHz

Aerial output

: UHF channels (Adjustable E28 – E60)

Memory backup time

: Approx. 6 months

Estimated figure based on supplied 
fresh battery; actual performance may 
differ.

ACCESSORIES

Provided accessories

: RF cable,

Lithium battery CR2025,
Infrared remote control unit,
“R6/UM-3” battery x 2,
Conversion plug*

HR-J491MS-ENnew.fm  Page 16  Tuesday, April 16, 2002  1:43 PM

Summary of Contents for HR-J491MS

















Reviews: