(No.YF183)1-7
3.2.2 ASSEMBLY/DISASSEMBLY OF CABINET PARTS AND ELECTRICAL PARTS
z
Disassembly procedure
NOTE1:
When removing the BOTTOM COVER ASSY, open and pull
up the COVER (SD).
NOTE4:
Pull out the GRIP BELT from the hook and leave it released
before removing the HDD COVER ASSY.
NOTE5a:
Remove the GASKET before starting the procedure.
NOTE5b:
During the procedure, be careful in handling the parts. Pay
special attention not to give any external shock to the HDD.
NOTE5c:
When the HDD is replaced, be sure to refer to 2.1 Replacing
HDD in "SECTION2 SPECIFIC SERVICE INSTRUCTIONS"
for the procedure after HDD replacement.
NOTE5d:
Be careful as the GELS at the four corners are easily come
off when the HDD is removed from the main unit. If the
GELS come off, be sure to attach them in the correct direc-
tion shown in the figure.
Attach the GELS with their HOLES on the same side of the
connector.
NOTE5e:
When connecting the FPC to the connector, insert the FPC
straight into the connector. When locking the connector, be
careful not to give so much load that it bends the board.
NOTE5f:
In this procedure, the FPC connected to the HDD connector
is not removed. If the FPC is removed due to broken wire,
be careful in attachment direction. Be sure to connect the
STOPPER side to the HDD.
Pay attention as wrong attachment could damage the HDD.
NOTE5g:
Be careful with the wiring.
NOTE8:
When attaching, fit the guide pin into the hole.
NOTE11a:
During the procedure, do not touch the terminals (elec-
trodes).
NOTE11b:
When attaching, be careful with the wiring .
NOTE12a:
During the procedure, be careful to avoid electric shock
caused by the STROBE CAPACITOR.
During the procedure, be careful to avoid electric shock.
NOTE12b:
Refer to [21] OPE BOARD ASSY and afterward for the dis-
assembly of UPPER ASSY.
NOTE13a:
During the procedure, be careful to avoid electric shock
caused by the STROBE CAPACITOR.
NOTE13b:
When attaching, be careful with the wiring (MIC).
NOTE13c:
Refer to [17] MIC BOARD ASSY and afterward for the dis-
assembly of FRONT ASSY.
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
[11]
[12]
[13]
[14]
[15]
[16]
[17]
[18]
[19]
[20]
[21]
[22]
[23]
[24]
3-2-1
3-2-2
3-2-3-1
3-2-3-2
3-2-4
3-2-5
3-2-6
3-2-7
3-2-8
3-2-9
3-2-10
3-2-11
3-2-12
3-2-13
3-2-14
3-2-15
3-2-16
3-2-17
3-2-18
3-2-19
3-2-20-1
3-2-20-2
3-2-21-1
3-2-21-2
3-2-22
3-2-23
NOTE1
-
-
NOTE4
-
NOTE5a,b,c,d,e,f,g
-
-
NOTE8
-
-
NOTE11a,b
NOTE12a,b
NOTE13a,b,c
NOTE14
-
NOTE16a,b
NOTE17
-
NOTE19a,b
NOTE20
NOTE21a,b,c
NOTE22
-
NOTE24a,b
B. COVER(5M) ASSY
SHOE ASSY
TOP COVER
HDD COVER ASSY
HDD
HDD CASE ASSY
BKT(HOOK)
OPE UNIT
DIAL UNIT
REAR COVER ASSY
BATT BOARD ASSY
UPPER ASSY
FRONT ASSY
MAIN BOARD ASSY
SHIELD MAIN ASSY
OP BLOCK ASSY
MIC BOARD ASSY
SENS BOARD ASSY
STROBE UNIT
MIC
OPE. BOARD ASSY
SPEAKER
COVER(HINGE)
MONITOR ASSY
STEP
No.
PART NAME
Fig.
No.
POINT
NOTE
4(S1),L1a,3(L1b)
2(S2),L2
2(L3)
GRIP BELT
2(S4a)
2(S4a),S4b,L4a,b,c,d
GASKET
CN5
4(S6a),S6b
S7,L7
CN8,S8a,b,L8a,b,c
CN9,S9a,b,L9
4(S10a),S10b,L10
S11,2(L11),CN11
CN12,3(S12),L12a,2(L12b)
CN13a,b,c,d,3(S13),L13a,
2(L13b)
CN14a,b,2(S14)
3(S15)
3(S16),FRAME ASSY
S17
(S18),2(L18)
3(S19),(L19)
S20a,b,COVER (MIC) ASSY
CN21a,4(S21),2(L21a),
L21b,CN21b
SPACER,2(S22),
L22a,b,c,BKT(SPEAKER)
(S23)
2(S24),2(L24)
