(No.YF244<Rev.001>)1-7
3.2.2 Assembly/Dissambly of cabinet parts and electrical parts
z
Disassembly procedure
NOTE1:
When removing the BOTTOM COVER ASSY, open and pull
up the COVER (SD).
NOTE2:
During the procedure, remove the HOOD (ACC) ASSY if
necessary by turning it to the direction of the arrow.
NOTE3:
When removing the TOP COVER ASSY, remove the screw
(No.7) by sliding the JACK COVER (DC).
NOTE4:
When removing the GRIP COVER ASSY, pull out the GRIP
BELT from the HOOK first.
NOTE5a:
During the procedure,confirm whether the part of two hooks (L5b)
of bracket (G. COVER) puts the part in the ditch of case (HDD).
NOTE5b:
During the procedure, be careful in handling the parts. Pay
special attention not to give any external shock to the HDD.
NOTE5c:
When the HDD is replaced, be sure to refer to "SECTION2
SPECIFIC SERVICE INSTRUCTIONS" for the procedure
after HDD replacement.
NOTE5d:
Be careful as the RUBBER SPACER set on both sides of the HDD
are easily removed when the HDD is removed from the main unit.
When reattaching the RUBBER SPACER, be careful in the
attachment direction.
NOTE5e:
In this procedure, the FPC connected to the HDD connector is
not removed. If the FPC is replaced due to broken wire or other
reasons, be careful with the attachment direction. Be sure to
connect the STOPPER side to the HDD as shown in the figure.
Pay attention as wrong attachment could damage the HDD.
NOTE8:
During the procedure, be careful in handling the FPC.
NOTE9a:
When removing the FRONT ASSY, first pull out the FPC
from the MONITOR ASSY, and then pull out the FPC from
the FRONT ASSY (LENS BARRIER) located underneath.
NOTE9b:
When attaching, be careful with the wiring .
NOTE9c:
Refer to Figs.3-2-16 for the disassembly of the FRONT ASSY.
NOTE10:
Refer to Figs.3-2-19 for the disassembly of the UPPER ASSY.
NOTE11:
Remove the FAN MOTOR as attached to the BKT FRAME (FAN)
and RUBBER SPACER, and disassemble them if necessary.
NOTE13:
When attaching, be careful with the wiring .
NOTE14:
During the procedure, be careful in handling the FPC. Pay
special attention not to damage the FPC when removing as
the HEAT SHEET affixed to the IC3001 is firmly stuck to the
FRAME ASSY and hard to remove.
NOTE16a:
Refer to 3.2.3 Assembly/Disambly of [16] OP BLOCK ASSY/
CCD BOARD ASSY of the OP BLOCK ASSY.
NOTE16b:
When attaching, be careful with the attachment location of
the SPACER.
NOTE21a:
When removing, remove the screw No.53 first to release the FPC.
NOTE21b:
During the procedure, be careful in handling the switches.
NOTE22:
When attaching, be careful with the wiring .
NOTE23:
Refer to 3.2.4 Disassembly of [23] MONITOR ASSY of the
MONITOR ASSY.
z
Destination of connectors
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
[11]
[12]
[13]
[14]
[15]
[16]
[17]
[18]
[19]
[20]
[21]
[22]
[23]
3-2-1
3-2-2A,B
3-2-3
3-2-4
3-2-5
3-2-6
3-2-7
3-2-8
3-2-9
3-2-10
3-2-11
3-2-12
3-2-13
3-2-14
3-2-15
3-2-16
3-2-17
3-2-18
3-2-19
3-2-20
3-2-21
NOTE1
NOTE2
NOTE3
NOTE4
NOTE5a,b,c,d,e
-
-
NOTE8
NOTE9a,b,c
NOTE10
NOTE11
-
NOTE13
NOTE14
-
NOTE16a,b
-
-
-
-
NOTE21a,b
NOTE22
NOTE23
BOTTOM COVER ASSY
SHOE ASSY
TOP COVER ASSY
GRIP COVER2 ASSY
HDD
WINDOW IR
CASE(HDD) ASSY
OPE UNIT
FRONT ASSY
UPPER ASSY
FAN MOTOR
REAR COVER ASSY
REG BOARD ASSY
MAIN BOARD ASSY
AUDIO BOARD ASSY
OP BLOCK ASSY
CDS BOARD ASSY
MIC
FRONT COVER ASSY
BARRIER ASSY
OPE BOARD ASSY
SPEAKER
MONITOR ASSY
4(S1),2(L1a),4(L1b)
2(S2),2(L2)
S3a,2(S3b),L3a,b,c,d,
2(L3e), JACK COVER
GRIP BELT,
2(S4),L4a,b,2(L4c)
3(S5),BKT(G.COVER),
L5a,2(L5b),CN5
S6,L6
3(S7),2(L7)
CN8,4(S8),2(L8)
CN9a,b,c,2(S9a),3(S9b)
CN10,S10a,3(S10b),L10
CN11,S11,2(L11),
RUBBER SPACER,
BKT FRAME(FAN)
3(S12)
CN13a,2(L13),CN13b
CN14a,b,c,2(S14)
S15,L15
CN16,3(S16)
S17,BKT FRAME(CDS),
L17a,2(L17b)
2(S18),2(L18a),S18,2(L18b),
PLATE(MIC),COVER(MIC),
CASE MIC
S19a,4(S19b)
2(S20)
S21,CN21,2(S21),2(L21)
S22,L22a,b,BKT(SPK)
2(S23),2(L23)
STEP
No.
PART NAME
Fig.
No.
POINT
NOTE
CN.
No.
PIN
No.
CONNECTOR
CN5
HDD
-
MAIN
CN110
40
CN8
OPE UNIT 2
-
MAIN
CN109
15
CN9a MONITOR
CN703
MAIN
CN104 26/32
CN9b LENS
BARRIER
-
MAIN
CN111 10
CN9c MIC
-
AUDIO
CN201 4
CN10 SPEAKER
-
AUDIO
CN202 2
CN11 FAN
MOTOR
-
MAIN
CN108 3
CN13a REG
CN6001
MAIN
CN103 50
CN13b REG
CN6002
CDS
CN4102
5
CN16 CDS
CN5001
CCD
CN5501 50
CN21 MAIN
CN
104
OPE
CN501 32/6
