JVC GR-D650AA, Instructions Manual

Page: 45 / 56

EN
45
EDITING
MasterPage: Start_Right
AD
V
A
N
C
ED
F
E
A
T
UR
ES
The audio track can be customised only when
recorded in the 12-BIT and SP modes.
(
墌
pg. 33)
●
Use the provided remote control.
1
Play back the tape to locate the point where
editing will start, then press PAUSE (
9
).
2
While holding A. DUB (
D
) on the remote
control, press PAUSE (
9
). The “
9
D
” indicator
appears.
3
Press PLAY (
U
), then begin “narrating”.
Speak into the microphone.
●
To pause dubbing, press PAUSE (
9
).
4
To end Audio Dubbing, press PAUSE (
9
),
then STOP (
8
).
To hear the dubbed sound during playback
Set “NARRATION” to “ON” or “MIX”.
(
墌
pg. 32, 35)
NOTES:
●
Sound is not heard from the speaker during Audio
Dubbing.
●
When editing onto a tape that was recorded at
12-BIT, the old and new soundtracks are recorded
separately.
●
If you dub onto a blank space on the tape, the
sound may be disrupted. Make sure you only edit
recorded areas.
●
If feedback or howling occurs during TV playback,
move the camcorder’s microphone away from the
TV, or turn down the TV’s volume.
●
If you change from 12-BIT to 16-BIT in mid-
recording and then use the tape for Audio
Dubbing, it is not effective from the point where
16-BIT recording began.
●
During Audio Dubbing, when the tape moves to
scenes recorded in the LP mode, scenes
recorded in 16-BIT audio or a blank portion, Audio
Dubbing stops.
You can record a new scene into a previously
recorded tape, replacing a section of the original
recording with minimal picture distortion at the in
and outpoints. The original audio remains
unchanged.
●
Use the provided remote control.
NOTES:
●
Before performing the following steps, make sure
that “TIME CODE” in both Recording and
Playback Menus is set to “ON”.
(
墌
pg. 32, 34, 35)
●
Insert Editing is not possible on a tape recorded in
the LP mode or on a blank portion of a tape.
1
Play back the tape, locate the Edit-Out point
and press PAUSE (
9
). Confirm the time code at
this point. (
墌
pg. 22)
2
Press REW (
3
) until the Edit-In point is
located, then press PAUSE (
9
).
3
Press and hold INSERT (
I
) on the remote
control, then press PAUSE (
9
). The “
9
I
”
indicator and the Time Code (min.:sec.) appear
and the camcorder enters Insert-Pause mode.
4
Press START/STOP to begin editing.
●
Confirm the insert at the time code you checked in
step
1
.
●
To pause editing, press START/STOP . Press it
again to resume editing.
5
To end Insert Editing, press START/STOP ,
then STOP (
8
).
NOTES:
●
Program AE, Effects and Shutter Effects
(
墌
pg. 40) can be used to spice up the scenes
being edited during Insert Editing.
●
During Insert Editing, the date and time
information changes.
●
If you perform Insert Editing onto a blank space on
the tape, the audio and video may be disrupted.
Make sure you only edit recorded areas.
●
During Insert Editing, when the tape moves to
scenes recorded in the LP mode or a blank
portion, Insert Editing stops. (
墌
pg. 49)
Audio Dubbing
PAUSE
PLAY
A.DUB
STOP
REW
INSERT
START/
STOP
Speaker
Stereo Microphone
Insert Editing
GR-D650AA.book Page 45 Tuesday, May 30, 2006 9:31 AM