10
Precautions
• Before making connections, turn off all the equipment.
• Use a cord whose plugs are correctly matching for the terminals on this Monitor and the equipment.
• Plugs should be firmly inserted; poor connection could cause noise.
• To unplug a cord, be sure to grasp its plug and pull it out.
• Connect the power cord after having finished all other connections.
• Refer also to the user manual of each piece of equipment.
Available Signals
Video signals
The following signals can be input to this Monitor:
•
VIDEO A
and
VIDEO B
terminals accept — PAL, PAL60, NTSC, NTSC4. 43, and SECAM signals.
•
COMPONENT/RGB B
terminals accept — 480i, 576i, 480p, 576p, 720/60p, 1080/60i (1035/60i), and 1080/50i signals. (You
need to set “RGB/COMPO.” to “COMPO.” on the menu (see page 22)).
Computer signals (Preset)
This Monitor has 18 preset video modes for the most popular industrial standard, and the signals of the following image
resolutions can be input to the RGB input terminals.
1
PC98
640
400
24.8
56.4
Non-interlace
2
VGA400-70
640
400
31.5
70.1
Non-interlace
3
VGA480-60
640
480
31.5
59.9
Non-interlace
4
VGA480-72
640
480
37.9
72.8
Non-interlace
5
VGA480-75
640
480
37.5
75.0
Non-interlace
6
WVGA-60
852
480
31.7
60.3
Non-interlace
7
MAC13”
640
480
35.0
66.7
Non-interlace
8
SVGA-56
800
600
35.2
56.3
Non-interlace
9
SVGA-60
800
600
37.9
60.3
Non-interlace
10
SVGA-72
800
600
48.1
72.2
Non-interlace
11
SVGA-75
800
600
46.9
75.0
Non-interlace
12
XGA-60
1024
768
48.4
60.0
Non-interlace
13
XGA-70
1024
768
56.5
70.1
Non-interlace
14
XGA-75
1024
768
60.0
75.0
Non-interlace
15
XGA-85
1024
768
68.7
85.0
Non-interlace
16
XGA+-75
1152
864
67.5
75.0
Non-interlace
17
RGB15K-60
—
—
15.7
59.9
Interlace
18
RGB15K-50
—
—
15.6
50.0
Interlace
Notes:
• When a signal other than listed above is input, a part of the screen may become void or an unnecessary picture may appear.
• Signals, though they are within the acceptable range of frequencies, may not be displayed normally, depending on the signal
type.
• Depending on the connected equipment, the Monitor may not be compatible with composite sync (Cs) or G on sync signals.
• When a preset mode signal is input, the vertical frequency displayed on the screen will have an “*” shown at its right top
position.
• When the No. 6 signal is input, change the aspect ratio to “FULL” with the ASPECT button (page 15) on the remote control or
from the “FUNCTION SELECT” menu (page 21).
• When No. 8 to No. 16 signals are input, thin lines may become obscure for their signal frequencies are higher than the screen
resolution.
Connections
Screen resolution
Horizontal
Vertical
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
Signal name
Scan system
No.
EN04_13_GM_V42E&EB.p65
04.2.5, 3:20 PM
10
