manualshive.com logo in svg

JVC DT-V9L3D, Instructions Manual, Page: 30 / 46

Share
Download
JVC DT-V9L3D Instructions Manual Download Page 30

8

7

 Rear  panel

Daily Operations / Connections 

(cont.)

8

1

 POWER switch

Turns AC power on or off.
•  You need to press 

 button (

☞

 

w

 on page 6) 

to use the monitor after turning on the POWER 
switch.

2

  AC IN terminal

AC power input connector.
Connect the provided AC power cord to an AC 
outlet.
•  Attach the provided power cord holder to prevent 

accidental disconnection of the AC power cord (

☞

 

“Attaching the Power Cord Holder” on page 9).

3

 DC switch

Turns the DC 12 V power on or off.
•  You need to press 

 button (

☞

 

w

 on page 

6) on the front panel to turn on the monitor after 
turning on the DC switch.

•  The monitor consumes the battery even while the 

monitor is on standby. To save battery life, turn 
off the DC switch.

4

  DC IN terminal

DC 12 V (maximum DC 17 
V) power input connector.
•  While using both the 

AC and DC 12 V power 
supply, AC power supply 
is preferentially used. If the AC power supply is 
cut off (for example, when turning off the POWER 
switch), the power supply automatically switches 
to the DC 12 V power supply.

5

  VIDEO/COMPONENT terminals (BNC)

IN:

 Input terminals for the composite (VBS) and the 

analog component (Y/P

B

/P

R

) signals.

•  Select the signal type in “VIDEO/COMPO. SEL.” 

corresponding to the type of the input signal (

☞

 

page 10).

OUT:

 Output terminal for the composite (VBS) and 

the analog component (Y) signals.

6

  AUDIO IN terminal (pin jack)

Input terminal for the analog audio signals.
•  Use this terminal for the analog audio connection 

of the SDI.

7

  E. AUDIO HD/SD SDI (SWITCHED OUT) terminal 

(BNC)

Output terminal for the HD/SD SDI signals.
•  The SDI signals of the current input (SDI 1 or SDI 

2) are re-clocked, then emitted.

•  When an input other than SDI 1 and SDI 2 is 

selected, the SDI signal of the input selected last 
time is emitted from this terminal.

•  The signals are emitted from this terminal only 

when the monitor is on or in “P.SAVE” (power 
save) mode.

8

  E. AUDIO HD/SD SDI (IN 1, IN 2) terminals (BNC)

Input terminals for the HD/SD SDI signals.
•  The terminals accept also EMBEDDED AUDIO 

signals including up to 12 audio channels with a 
sampling frequency of 48 kHz.

9

  AUDIO (MONITOR OUT) terminals (pin jack)

Output terminals for the analog audio signal.
•  The terminals emit the audio signals coming 

in from the AUDIO IN terminal or EMBEDDED 
AUDIO signals coming in from the E. AUDIO HD/
SD SDI (IN 1 or IN 2) input terminal. (

☞

 “Audio 

Channel Selection”  on page 7)

•  The signal is output from these terminals only 

when the monitor is on or in “P.SAVE” (power 
save) mode. (

☞

 “NO SYNC ACTION” in “SYNC 

FUNCTION” on page 13)

•  The EMBEDDED AUDIO signal...

– is decoded into an analog signal, then emitted.
– is emitted only when “SDI 1” or “SDI 2” is 

selected, and when EMBEDDED AUDIO 
signals come in to the E. AUDIO HD/SD SDI 
(IN 1 or IN 2) terminal.

When using DC 12 V power (maximum DC 17 V), 
check the DC IN terminal pin signal, and use the 
correct polarity. If the polarity is reversed, this 
could cause a fire or personal injury.

p

 REMOTE terminals

Terminals for controlling the monitor by an external 
control. (

☞

 “External Control” on page 16)

q

 Carry handle

Use this handle when carrying the monitor.

w

 Security slot

Attach a security wire to this slot.

e

  Screw holes for external battery attachment

Attach external battery for DC 12 V power supply 
by using 2 screw holes. Choose the appropriate 
screw holes from 1, 2, 3 or 4, according to the type 
of external battery.
•  Use the Anton Bauer Dionic 90 (mount: QR DXC-

M3A) external battery.

CAUTION

• 

Do not use the external battery for DC 24 V 
power supply.

•  Use only the battery specified above. If a heavy 

battery is used, it may fall off depending on the 
way the monitor is used.

Note for connections

•  Before making any connections, turn off all the 

equipment.

•  Use a cord whose plugs correctly match the 

terminals on this monitor and the equipment.

•  Plugs should be firmly inserted; poor connections 

could cause noise.

•  When unplugging a cord, be sure to grasp its plug 

and pull it out.

•  DO NOT connect the power cord until all connections 

are complete.

•  Refer also to the user manual of each piece of 

equipment.

CAUTION

Do not connect the power cord until all 
other connections are completed.

DT-V9L3D_J_en.indb   8

DT-V9L3D_J_en.indb   8

09.8.7   1:30:29 PM

09.8.7   1:30:29 PM

Summary of Contents for DT-V9L3D















































Reviews:

No comments