Masterpage:Right0
EN
19
Filename [MV4S_05Name.fm]
Page 19
Monday, 9 May 2005 09:36
INITIAL SETTINGS
Auto Clock Set/Auto Tuner Set
This unit sets the clock and tuner channels automatically when AC
power cord is first connected to an AC outlet. The antenna cable
must be connected for the Plug & Play setting.
The time and date can be set automatically by the clock setting
data transmitted from one of the regular TV broadcast channels.
We call this TV channel the “host channel” and it is a PBS channel
in your area.
1
Connect the antenna cable to the unit. (
connect the AC power cord to an AC outlet. Do not turn on the unit.
The clock and tuner channels will be set automatically.
●
“LOADING” blinks on the front display panel when the AC plug of the
AC power cord is connected into an AC outlet and it takes
approximately 50 seconds for the unit to be turned on. This is not a
malfunction.
NOTES:
●
Auto Clock Set is performed first.
“AUTO” blinks on the front display panel during Auto Clock Set.
●
Auto Channel Set is performed next. Auto Channel Set scans all the
channels that are receivable by your unit. During Auto Channel Set,
the channel numbers are displayed as they are scanned and set.
●
When Plug & Play setting has been completed successfully, the
correct clock time is displayed. If you perform Plug & Play setting
successfully, there is no need to perform “Clock Set” (
pg. 22). If, however, you want to add or delete
channels, refer to “Manual Channel Set” (
Plug & Play Set
ATTENTION:
●
If you use a cable box, Plug&Play will not function; set the clock
and tuner channels separately. (
●
Depending on areas or reception conditions, the unit may not
receive the Auto clock setting data from the PBS channel. If this
function is taking a considerable amount of time, it may be
necessary to perform the Semiauto or Manual Clock Set
procedure.
INFORMATION
●
If “AUTO CLOCK ” is set to “ON” (
pg. 21), the clock will be
adjusted automatically by the host channel every hour (except
11:00 PM, midnight, 1:00 AM and 2:00 AM) using the incoming
PBS channel clock setting data. (This automatic clock adjustment
can only be performed when the unit is turned off. The clock will be
adjusted just on these hours — on the time displayed on the front
display panel, not on the actual real time.) The default setting of
“AUTO CLOCK ” is “ON”. (
●
If the memory backup fails, because a power outage occurs or
because the AC power cord is unplugged, Plug & Play will be
performed when power is restored to the unit.
What to do if Plug & Play setting failed
●
If an incorrect time is displayed on the front display panel, you may
be receiving the clock setting data of a PBS channel from an
adjacent time zone, or an incorrect PBS channel from a cable TV
system. In this case, perform “Semiauto Clock Set” (
●
If “– –:– –” appears on the front display panel, your antenna cable
may not be connected to the unit or there may not be a Host PBS
signal available in your area. Ensure that the antenna cable is
connected correctly. Then turn on and off the unit; the Plug & Play
setting will be automatically reactivated. If Plug & Play setting is not
performed though the antenna cable is connected correctly,
perform “Manual Clock Set” (
pg. 21) and “Auto Channel Set”
pg. 22) or “Manual Channel Set” (
V
HS/D
V
D
D
V
D
V
HS
REC
V
HS
D
V
D
DUBBI
N
G
CH
STA
N
DBY/O
N
S-
V
IDEO
V
IDEO
AUDIO
ONE‑TOUCH EXPERT DUB
DVD
(MONO)
F−1
During Auto Clock Set
“AUTO” blinks.
During Auto Channel Set
The channel numbers are displayed and “AUTO” blinks as they
are scanned and set.
Plug&Play Completed
The current time is displayed.
●
If an incorrect clock time or “– –:– –” appears on the front display
panel, see “What to do if Plug & Play setting failed” (
MV4S_05Name.fm Page 19 Monday, May 9, 2005 9:36 AM
