Filename [DR-MH30UJ_07Timer Recording.fm]
Masterpage:Left+
48
EN
TIMER RECORDING
Page 48
Monday, 12 July 2004 14:25
You can program this unit to timer-record as many as 32 programs.
If you do not know the VCR Plus+ number for the program you
wish to record, use the following procedure to set your unit to
timer-record the program.
1
Load a recordable disc if recording to DVD.
2
Press
PROGRAM
to access the program top screen.
3
Press
rtw e
to select “CALENDAR PR.”, then press
ENTER
.
●
When “PROGRAM FULL DELETE UNWANTED TIMER
PROGRAMS” appears on the TV screen, you need to cancel some of
the reserved programs. (
墌
pg. 49)
4
Press
rtw e
to select the desired date, then press
ENTER
.
5
Press
rt
to select “RECORD
TO”, then press
ENTER
. Press
rt
to select the desired
recording deck, then press
ENTER
.
6
Press
rt
to select “START”, then press
ENTER
. Press
rt
to
set the desired start time, then press
ENTER
.
●
Each press of
rt
advances/goes back the start time in 1-min.
increments.
●
To advance/go back the start time in 30-min. increments, press and
hold
rt
.
7
Press
rt
to select “STOP”, then press
ENTER
. Press
rt
to
set the desired stop time, then press
ENTER
.
●
Each press of
rt
advances/goes back the stop time in 1-min.
increments.
●
To advance/go back the stop time in 30-min. increments, press and
hold
rt
.
8
Press
rt
to select “SOURCE”, then press
ENTER
. Press
rt
to select the desired source, then press
ENTER
.
9
Press
rt
to select “CH”, then press
ENTER
. Press
rt
to
select the desired channel.
10
Press
rt
to select “CONFIRM”, then press
ENTER
.
11
Set the other recording options as required.
●
Refer to step
8
in “VCR Plus+
®
Timer Programing” (
墌
pg. 46).
12
Press
rt
to select “OK”,
then press
ENTER
to access the
Program Confirmation screen.
13
Press
w e
to select “EXIT”,
then press
ENTER
to complete
timer programing.
●
To program another timer, press
w e
to select “CONTINUE”,
then press
ENTER
.
●
If “PROGRAM OVERLAPPED” appears on the TV screen, see
page 49.
NOTES:
●
When two successive programs are recorded on a DVD-RW disc with
Manual Timer Programing function, the beginning of the second one
may be left off the recording.
●
If the copy limited program is received during timer-recording, the unit
enters Record Pause mode. Recording starts again if it is switched to
a recordable broadcast during the time you programed.
Manual Timer Programing
●
Make sure that the unit’s built-in clock is set properly.
●
Turn on the unit.
●
Turn on the TV and select the AV mode.
●
Slide the
TV/CABLE/DBS/DVD
switch to
DVD
.
rtwe
AUX
PROGRAM
ENTER
CABLE/DBS
DVD
TV
01/08/03 WED 10:30PM - 11:00PM
DBS 100
[MISC. ] XP
PRESS [PROGRAM]
TO EXIT
SELECT WITH [ ]
THEN PRESS [ENTER]
100
CH
DBS
SOURCE
11:00PM
STOP
10:30PM
START
HDD
RECORD TO
PROGRAM > CALENDAR PROG. (2/3)
O K
ENTER
SELECT
EXIT
PROGRAM
2
Cable Box and DBS Receiver Users
To timer-record a satellite broadcast using Manual Timer
Programing:
A
Perform “Cable Box and/or DBS Receiver Control Setting”
(
墌
pg. 24).
B
Perform “Manual Timer Programing” (
墌
pg. 48).
C
Leave the cable box or DBS receiver’s power on.
Relief Recording
When a program that is set for the DVD deck cannot be recorded
properly, the program is recorded to the HDD deck instead in the
same recording mode as set.
●
If the remaining capacity of the hard disc is not sufficient, the
program is recorded to the DVD deck until the remaining capacity
of the DVD disc lasts.
●
If “JUST” is selected for the recording mode, the current recording
mode for the DVD deck is applied.
01/08/03 WED 10:30PM - 11:00PM
DBS 100
[EDUCATION]
GARDENING
FR360
1:00
28:00
ENTER
SELECT
EXIT
PROGRAM
PRESS [PROGRAM]
TO EXIT
SELECT WITH [ ]
THEN PRESS [ENTER]
FR360
REC MODE
MON-FRI (FOR A WEEK)
WEEKLY/DAILY
EDUCATION
CATEGORY
GARDENING
INPUT TITLE
PROGRAM > CALENDAR PROG. (3/3)
O K
2
DR-MH30UJ_00.book Page 48 Monday, July 12, 2004 3:17 PM
