JVC DR-DX5SEK, Instructions Manual

Page: 61 / 92

Masterpage:Right+
EN
61
Filename [DX5SEK_12Editing.fm]
EDITING
Page 61 Thursday, 10 November 2005 16:34
You can dub programmes from a camcorder or DV equipment
connected to the unit with a DV cable. The unit’s remote control
allows you the limited control of the connected camcorder or DV
equipment functions during dubbing.
The following on-screen display for DV dubbing appears when
ON SCREEN is pressed while the channel has been set to A DV B .
A
Remote control switch
To switch between the devices operable by the remote control
unit. The unit is operable when the remote icon (
)
displayed faces to the left, while the DV device is operable when
the remote icon is facing to the right.
B
Auto capture button
Select to start or pause the dubbing. If ENTER is pressed when
the DV device is in the pause condition, preroll editing* where it
is possible to dub with a start time that is highly accurate will be
activated. When the DV device cannot be operated from the unit
(such as in camera mode), proceed with normal recording
(
A
pg. 34, 37).
●
Do not start dubbing at the portion with no time code ( A – –:– –:– – B ).
* Preroll editing refers to the playback after the DV tape is slightly rewind.
(For DV devices that do not support the –1x speed, the rewinding time
may be longer.)
C
Sound monitor switch
For selecting the desired sound format for dubbing.
1
Connect a camcorder or DV equipment to the [DV IN] connector
on the unit’s front panel.
2
Press DV/HDD/DVD SELECT on the unit repeatedly; or press
HDD or DVD on the remote control to select the recording deck.
●
When dubbing to a DVD disc, load a recordable disc on this unit.
3
Press PR +/– to set the channel to A DV B .
4
Press ON SCREEN.
●
The on-screen display for DV dubbing appears.
5
Press selection keys to select , then press ENTER
to display the remote icon (facing to the right) for the DV
equipment.
6
Press REC MODE repeatedly to set the recording mode. For
DV deck, press REC MODE on the remote control to set the
recording mode.
7
Locate the point from where you want to start dubbing, then
stop or pause playback by pressing the following buttons on the
remote control:
I
,
N
,
O
,
o
,
W
.
●
To play back in slow speed (1/10 of the normal speed), press
W
to pause playback, then press
O
or
N
.
●
To play back frame-by-frame, press
W
to pause playback, then
press
W
repeatedly. Each press of
W
advances a frame.
●
To change the playback direction, press
O
or
N
.
8
Press selection keys to select , then press ENTER
repeatedly until the desired sound track appears on the TV
screen.
SOUND1
:
Select this to record the original stereo sound played back on
the connected DV equipment.
SOUND2
:
Select this to record the dubbed stereo sound played back on
the connected DV equipment.
MIX
:
Select this to record the sound of both A SOUND1 B and
A SOUND2 B .
●
Note that this selection is not available when the source
programme is recorded in 16BIT (48 kHz) mode.
9
Press selection keys to select , then press
ENTER . The dubbing starts.
●
Playback on the external DV equipment and recording on the
unit should start simultaneously.
●
To pause dubbing, press selection keys to select ,
then press ENTER . Both the unit and the external DV
equipment pause dubbing. Pressing
W
on the unit also works
the same way.
10
Press selection keys to select , then press
ENTER . Then press
o
. The DV equipment stops.
11
Press selection keys to select , then press
ENTER .
12
Press
o
twice on the remote control to stop dubbing.
●
Both the unit and the external DV equipment stop dubbing.
NOTES:
●
Dubbing copyright guarded programmes is not possible.
●
Original DV information such as the recording date and time are
not recorded.
●
The superimposed indication during the operation or dubbing is
not recorded.
●
If the dubbing is paused while the channel is set to
A
DV
B
, you
cannot switch channels.
To skip unwanted part of the source picture
Press ENTER to stop both equipment, then press selection keys
to select .
Locate the point where you want to restart dubbing by pressing
I
,
N
, or
O
, then press
o
.
Press selection keys to select , then press ENTER to
restart dubbing.
DV Dubbing (HDD & DVD Deck Only)
NOTES:
●
When connecting the unit to a device equipped with a DV input
connector, be sure to use the optional DV cable (VC-VDV
204U).
●
When you connect a PC to the [DV IN] connector, we do not
assure the normal operation of this unit.
To [DV IN]
DV cable
(VC-VDV 204U)
(not supplied)
Camcorder
DV connector
Your unit
DV equipment
L – R
SOUND1
0:00 1:00 2:00
GR-DV3500
GR-DV3500 DV
HDD
00:00:00. 00
12bit JVC
00:00:00. 00
DV
FR360
DV DV
1 2
A B C
When you dub from DV equipment other than a
camcorder
A
Perform step 1 to 4 .
B
Locate the point from where you want to start dubbing,
then stop on the DV equipment.
●
If you pause the DV equipment in this step, a few
second’s still picture will be recorded at the beginning of
the recorded programme.
C
Set the input mode to
A
DV INPUT
B
on the DV equipment.
●
If you select an input mode other than A DV INPUT B ,
unwanted pictures may be recorded at the beginning of
the recorded programme.
D
Perform step 9 to 12 .
DX5SEK_00.book Page 61 Thursday, November 10, 2005 4:35 PM