JVC CA-UXG980V Instructions Manual Download Page 59

Page: 59 / 70

Additional Information

Learning More about This System

Connections (see pages 4 to 6)

• Make sure the antenna conductors do not touch any

other terminals, connecting cords or the power cord.
Also, keep the antennas away from metallic parts of the
System, connecting cords, and the power cord. These
could cause poor reception.

• Use only speakers with the same speaker impedance

as indicated by the speaker terminals on the rear of the
System.

• The speakers are magnetically shielded to avoid color

distortions on TVs. However, if not installed properly,
it may cause color distortions. So, pay attention to the
following when installing the speakers.

– When placing the speakers near a TV set, turn off the

TV’s main power switch or unplug it before installing
the speakers.
Then wait at least 30 minutes before turning on the
TV’s main power switch again.

– Some TVs may still be affected even though you have

followed the above instructions. If this happens, move
the speakers away from the TV.

Daily Operations—Playback (see pages 8 to 13)

Listening to the Radio:

• If you store a new station into an occupied preset

number, the previously stored station in that number will
be erased.

Playing Back a Disc/USB Mass Storage Class Device:

JVC bears no responsibility for any loss of data in the
USB mass storage class device while using this System.

• When you change the source to “DVD/CD,” “USB

MEMORY 1,” or “USB MEMORY 2,” it may take a while
to activate the source.

• While the System is reading a disc, the source may not

change to “USB MEMORY 1” properly. In this case, press

, then change the source to “USB MEMORY 1.”

• On some discs, the actual operations may be different

from what is explained in this manual due to the
programming and disc structure; such differences are not
a malfunction of this System.

• The total number of tracks (files) that the System can

detect is 4 000 for “DVD-CD” and “USB MEMORY 1,”
and 2 000 for “USB MEMORY 2”.

•  The System recognizes up to...
  – 999 tracks (files) per group.
  – 99 groups per disc.
  – 99 groups per USB mass storage class device connected

to the USB MEMORY 1 terminal.

– 999 groups per USB mass storage class device

connected to the USB MEMORY 2 terminal.

Unplayable files are also counted in the total file number.
Playable files which do not belong to any groups are

recognized as files of group 1.

• For playback of files in the USB mass storage class

device...

– When connecting a USB mass storage class device, refer

also to its manual.

– Connect one USB mass storage class device to each

terminal of the System at a time. Do not use a USB hub.

– You cannot charge any USB mass storage class device

through the USB terminals (

– While playing back a file in a USB mass storage class

device, do not disconnect the device. It may cause
malfunction on both the System and the device.

  – This System is compatible with USB 2.0 Full Speed.
  – You cannot play back a file larger than 2 Gigabytes.
  – When playing a file of a large transfer rate, frames or

sounds may be dropped during playback.

– This System cannot recognize a USB mass storage

class device whose rating is other than 5 V and exceeds
500 mA.

– This System may not play back some USB mass storage

class devices and does not support DRM (Digital Rights
Management).

– It will take some time to start up a digital audio player

whose contents are larger than 1 Gigabyte.

•  For DVD-VR playback...
  – This System can play only a disc of UDF-Bridge format.
  – For details about DVD-VR format and Play List, refer

to the manual of the recording equipment.

• For MP3/WMA/WAV playback...
– MP3/WMA/WAV discs require a longer readout time

than regular CDs. (It depends on the complexity of the
group/file configuration.)

– Some MP3/WMA/WAV files cannot be played back