JVC CA-MXK50R Page 15 Service Manual Download

Page: 15 / 70

1-15

MX-K50R

<CD mechanism section>

•

Removing the CD mechanism holder from the CD
chager unit.
(Refer to "Removing the CD mechanism holder
assembly" )

Removing the pickup unit (

See Fig.1)

1. Removing the cut washer on the feed gear
sleeve and pull out the feed gear.
2. Remove the two screws A fixing the pickup
shaft.

3. Removing the pickup unit.

Removing the feed motor (

See Fig.1)

Remove the two motor fixing screws at B and
removing the feed motor.

Removing the spindle motor

Removing the motor board

(See Fig.2)

1. Unsolder the motor terminal on the motor board.

2. Remove the moter board.

The spindle motor cannot be removed as a single
unit.
When removing the spindle motor, change the chasis
and turntable together as aunit.

Fig.2

Fig.1

Cut washer

Unsolder

Shaft

Feed Gear

Shutter

Pickup unit

Motor board

Unsolder Feed motor

Spindle motor

< Speaker section >

It is exchange in a unit.
Please do not decompose.

Summary of Contents for CA-MXK50R







































































Search results

Summary of Contents for CA-MXK50R

Reviews:

Related manuals for CA-MXK50R

Brands by name

Popular brands

JVC CA-MXK50R, Service Manual

Search results

Summary of Contents for CA-MXK50R

Reviews:

Related manuals for CA-MXK50R

Brands by name

Popular brands